Copper DWV 45° Elbows are wrought copper drain, waste and vent fittings that turn a pipe run by 45 degrees. NIBCO's H042500, for example, is a 1-1/4 inch copper by copper elbow with solder cups on both ends, and its 906-2 street elbows pair a solder cup with a male solder end in sizes from 1-1/4 inch to 3 inch. Plumbers use them in DWV systems wherever a run needs a 45 degree change of direction instead of a sharp 90. Two 45s set in sequence also build an offset or a full 90 degree turn when the layout calls for it. Fittings in this category come in copper by copper and street styles. Because both styles join by solder, matching the connection style and pipe size before assembly saves rework on the job and keeps the installation moving.
Subcategories
Buying Guide
Start with the connection style, because it decides how the fitting meets the rest of the run. A copper by copper (C x C) elbow has solder cups for pipe on both ends. A fitting by copper (Ftg x C) street elbow has one solder cup and one male solder end, so the male end seats into another fitting. Choose the style that matches what the joint touches.
Next, confirm the size. NIBCO lists its 906-2 street elbows in 1-1/4, 1-1/2, 2 and 3 inch, and its H042500 C x C elbow in 1-1/4 inch. Match the fitting to the pipe it receives, and check the part number against the drawing before soldering.
Then confirm the material. NIBCO builds these fittings from wrot copper and sells them for DWV systems. Mixing a DWV fitting into a pressure line is a spec question for the engineer or inspector, so verify intended use first.
When comparing Copper DWV 45° Elbows from different manufacturers, check the same three points on each catalog sheet: connection type, nominal size, and the system type the fitting is designed for. Part numbers differ between brands, so cross reference by description and size instead of assuming a one-to-one swap.
Finally, think about the whole assembly. Two 45s can build an offset or a 90 degree turn with a longer sweep. Counting each connection style and size early on the takeoff keeps the order accurate and the crew supplied.
Frequently Asked Questions
What's the difference between a C x C and a Ftg x C copper DWV 45° elbow?
A C x C copper DWV 45° elbow has a solder cup on each end for pipe. A Ftg x C elbow, usually called a street elbow, has one solder cup and one male solder end that seats into another fitting. NIBCO's H042500 is a C x C example, and its H044100 is a Ftg x C example.
What sizes do NIBCO copper DWV 45° street elbows come in?
NIBCO's 906-2 Ftg x C DWV 45° elbows are listed in 1-1/4, 1-1/2, 2 and 3 inch sizes. The material numbers are H044000, H044050, H044100 and H044150. Other brands and connection styles in the Copper DWV 45° Elbows category carry their own part numbers.
Can I use a copper DWV 45° elbow on a pressure line?
Copper DWV 45° elbows are sold for drain, waste and vent systems, and NIBCO describes its H042500 and H044100 as DWV fittings. Whether a DWV fitting is acceptable on any other line is a code and engineering question. Check the local code and the project spec before substituting.
When do I use two 45s instead of a 90 on a DWV run?
Two copper DWV 45° elbows set in sequence change the pipe direction by a total of 90 degrees, since each one changes direction by 45 degrees. Plumbers also pair them to build an offset around an obstruction. Check local code for fitting rules on the specific drain run.
What are NIBCO copper DWV 45° elbows made of?
NIBCO lists its H042500 and H044100 copper DWV 45° elbows as wrot copper construction. Both have soldered connections, either two solder cups or a solder cup plus a male solder end. NIBCO also lists a 50-year limited warranty on both.