Rheem Condensate Removal Pumps are automatic pumps that collect and discharge the condensate produced by air conditioners, heat pumps, dehumidifiers, and high-efficiency condensing furnaces and boilers. Standard 115 volt models move condensate at rates such as 65 gallons per hour at a 1 foot lift, while higher-capacity 115 volt models reach up to 270 gallons per hour at the same lift height for larger systems or multiple combined condensate lines. Compact mini-split condensate pumps handle the smaller volume typical of a single ductless zone, mounting directly alongside the indoor unit rather than a standard floor or shelf-mounted pump. Contractors install these pumps whenever gravity drainage to a floor drain or exterior discharge point is not available, routing condensate instead through a discharge tube up and over to a suitable drain location. Selecting a pump with enough capacity for the connected equipment's condensate output prevents overflow, nuisance safety switch trips, and water damage inside a mechanical room or attic space. Matching voltage, GPH capacity, and lift height to the installation keeps the pump running reliably for the life of the connected HVAC equipment.
Subcategories
Buying Guide
Start by identifying the connected equipment's condensate output and installation environment, since Rheem Condensate Removal Pumps come in different capacity ranges built for different jobs. A standard 115 volt pump rated around 65 gallons per hour at a 1 foot lift covers most single-system residential installations, while a high-capacity 115 volt model rated up to 270 gallons per hour handles larger systems or combined condensate lines from more than one piece of equipment. Confirm the lift height the pump needs to achieve, since capacity ratings typically drop as the vertical lift to the discharge point increases. High-efficiency condensing furnaces and boilers produce acidic condensate, so confirm the selected pump is rated for that application rather than only for air conditioner condensate. Ductless mini-split installations call for a compact pump sized to mount directly alongside the indoor unit rather than a standard floor or shelf-mounted model. Every pump should tie into the connected equipment's safety switch circuit, so a pump failure or reservoir overflow shuts down the cooling or heating equipment before water damage occurs. Routing the discharge tubing with a continuous upward or level slope to the drain point, without dips that trap water, keeps the pump from working against trapped condensate in the line. Checking local code for condensate drainage and safety switch requirements before finalizing the installation keeps the job compliant.
Frequently Asked Questions
How much condensate can a standard Rheem pump handle?
Standard 115 volt Rheem condensate pumps move condensate at rates around 65 gallons per hour at a 1 foot lift, which covers most single-system residential air conditioner and furnace installations. Systems producing more condensate, or setups combining multiple equipment lines into one pump, need a higher-capacity model instead. Confirming the connected equipment's condensate output before ordering keeps the pump from overflowing during peak load.
When does an installation need a high-capacity condensate pump instead of a standard model?
High-capacity 115 volt Rheem condensate pumps reach up to 270 gallons per hour at a 1 foot lift, suited to larger residential systems or installations that combine condensate from more than one piece of equipment into a single pump. A standard model rated around 65 gallons per hour covers most single-system jobs without that added volume. Reviewing total combined condensate output before selecting a pump prevents reservoir overflow.
Can the same condensate pump serve both an air conditioner and a condensing furnace?
High-efficiency condensing furnaces and boilers produce acidic condensate that requires a pump rated for that specific application, not just standard air conditioner condensate. Rheem offers pumps built to handle this acidic byproduct safely on the way to an approved drain. Confirming the pump's rated application before installation prevents premature pump failure from exposure to condensate it was not designed to handle.
Do mini-split systems need a different condensate pump than a central system?
Mini-split condensate pumps are built compact enough to mount directly alongside a ductless indoor unit where space is limited. Ductless installations typically produce less condensate volume than a whole-house central system, so the smaller pump size matches that lower volume. Choosing a compact mini-split pump instead of a standard model keeps the installation neat around the indoor unit.
What happens if a Rheem condensate pump fails?
Rheem condensate pumps tie into a safety switch circuit that shuts down the connected cooling or heating equipment if the pump fails or the reservoir overflows. Wiring the safety switch correctly during installation prevents water damage inside a mechanical room, attic, or closet from an undetected condensate leak. Testing the safety switch during startup confirms the protection is active before the job is complete.