CD-5080 Non-Hinged (Double Cam) Duct Access Doors are galvanized steel panels built for service access into sheet metal ductwork without a hinge assembly. Each door and frame is constructed from 24 gauge galvanized steel, with 1/8 inch thick closed cell neoprene gasketing sealing both the door-to-frame and frame-to-duct joints. The insulated version fills the door panel with 2 inch fiberglass insulation rated at 7.7 R factor, compressed to a 1 inch profile to limit heat transfer through the opening. A self-tightening, hand-operated cam latch holds the door closed and is rated for low to medium duct pressure up to 3 inches of static water gauge. Installers use this style where full removal of the door for duct cleaning or damper access matters more than a permanently attached hinge, and sizes range from 6 by 6 inches up to 24 by 24 inches to match different duct opening requirements.
Subcategories
Buying Guide
Choosing a duct access door starts with matching the door style to the duct material already installed. Sheet metal ducts take the standard CD-5080 Non-Hinged (Double Cam) Duct Access Doors, built from 24 gauge galvanized steel with a knock-over tab frame, while fiberglass ductboard systems need the CD-5080-F version with its adhesive-bonded trim flange instead.
Pressure rating comes next. The doors carry a rating for low to medium pressure applications up to 3 inches of static water gauge, which covers most residential and light commercial supply and return duct runs. Higher pressure duct systems, such as rooftop units or industrial exhaust runs, typically call for a different access door rated for the higher static pressure involved.
Insulation needs depend on where the duct runs. Ducts passing through unconditioned attics, crawlspaces, or exterior walls benefit from the insulated panel option, which fills the door with fiberglass insulation to match the R value of the surrounding duct insulation and avoid a cold or hot spot at the access point. Uninsulated ducts inside conditioned space can use the standard uninsulated panel without a thermal penalty.
Sizing rounds out the decision. Doors run from 6 by 6 inches for small dampers and sensors up to 24 by 24 inches for full technician access, with custom sizes available for openings outside the standard range. Match the door size to the largest tool or hand access needed for the specific service task behind it.
Frequently Asked Questions
What's the difference between the CD-5080 and the CD-5080-F duct access door?
The standard CD-5080 mounts to sheet metal duct with knock-over tabs on the frame, while the CD-5080-F is built for fiberglass ductboard and uses an adhesive-bonded trim flange for surface mounting. Both use the same non-hinged, double-cam latch design for removable access.
What pressure rating do CD-5080 duct access doors carry?
CD-5080 doors are rated for low to medium duct pressure up to 3 inches of static water gauge, which covers the great majority of residential and light commercial HVAC duct runs. Higher pressure systems typically need an access door rated for greater static pressure.
Do CD-5080 duct access doors come insulated?
An insulated version fills the door panel with 2 inch fiberglass insulation rated at 7.7 R factor, compressed to a 1 inch profile inside the panel. Contractors specify the insulated option on ducts running through unconditioned space to avoid a thermal gap at the access point.
What sizes are available for CD-5080 duct access doors?
Standard sizes run from 6 by 6 inches up to 24 by 24 inches, covering openings for sensors, small dampers, and full technician access. Custom sizes are available for ducts that fall outside the standard size range.
How does the latch work on a non-hinged double cam duct access door?
A self-tightening, hand-operated cam latch holds the door against the gasketed frame without a hinge attaching the panel to the frame. The latch design allows full removal of the door for cleaning or inspection rather than a swing-open panel that stays attached.