Control Kits are Field Controls products that operate venters and draft inducers or add appliance control to combustion air systems. The venter and burner control system reviewed for this page applies to all oil-fired systems and lists a draft proving switch, adjustable electronic post purge and secondary safety switch as features. The category also includes the CAC-120 and CAC-24 controls, which add a further appliance to a CAS combustion air system, where one CAS-3 or CAS-4 unit handles a maximum combined firing rate input of 500,000 BTU/Hr. The CAC-120 is a 120v control used with the CAS-3 on chimney-vented oil-fired systems, while the CAC-24 is a 24v control used with the CAS-4 on chimney-vented gas-fired systems. Choosing the correct kit for the fuel and the appliance matters because each kit is matched to specific equipment, and a mismatch means a return trip.
Subcategories
Buying Guide
Start with the fuel and the appliance. The venter and burner control system reviewed for this page is listed for all oil-fired systems, the CAC-120 is described for chimney vented oil fired systems using the CAS-3, and the CAC-24 is described for chimney vented gas fired systems using the CAS-4. Confirm the fuel on the job before narrowing the choice.
Next, match the voltage and the control model. The CAC-120 is a 120v control for the CAS-3, CAS-6 and CAS-7, and the CAC-24 is a 24v control for the CAS-4. When comparing Control Kits, read the model names in each title, since each kit names the CAS units it controls.
Then check the firing rate limit. One CAS-3 or CAS-4 unit handles a maximum combined firing rate input of 500,000 BTU/Hr, and a matching CAC control is required for each additional appliance on the same unit. Total the appliance inputs on the job before ordering.
Finally, check the replacement parts. The PPC-4 Thermal Post Purge Kit is listed as a replacement part for the CK-62, and the 24v Relay is listed for use with models PVG, CK-40F, 41F, 43F, 91F and 92F. Match the part to the model on the equipment, and confirm details with the manufacturer or the SupplyHouse team when the model is unclear. Careful matching keeps the repair to a single visit.
Frequently Asked Questions
What do Control Kits do on an oil-fired system?
The Field Controls venter and burner control system is one of the Control Kits listed for all oil-fired systems. Its description states it controls the operation of SWG/CV Power Venters and can also control Field Draft Inducers. Features listed include a draft proving switch, adjustable electronic post purge and secondary safety switch.
Which Control Kits work with the CAS-3?
Among the Control Kits, the CAC-120 is a 120v control for the CAS-3, CAS-6 and CAS-7, and it is described for chimney vented oil fired systems using the CAS-3. A CAC-120 is required for each additional appliance added to the same CAS-3 unit. One CAS-3 unit handles a maximum combined firing rate input of 500,000 BTU/Hr.
Is there a gas-fired control kit for combustion air systems?
Among the Control Kits, the CAC-24 is a 24v control for the CAS-4, described for chimney vented gas fired systems. A CAC-24 is required for each additional appliance added to the same CAS-4 unit. One CAS-4 unit handles a maximum combined firing rate input of 500,000 BTU/Hr.
What is the PPC-4 post purge kit for?
The PPC-4 Thermal Post Purge Kit from Field Controls is listed as a replacement part for the CK-62. It sits in the Control Kits category alongside other service parts. Confirm the model on the equipment before ordering.
What models does the Field Controls 24v relay work with?
The Field Controls 24v Relay is listed for use with models PVG, CK-40F, 41F, 43F, 91F and 92F. Control Kits and parts vary by model, so match the relay to the model on the equipment. Confirm with the manufacturer or the SupplyHouse team if the model is unclear.