Apply to be a TradeMaster!
Filter menu expanded

Filters

50 items
Reset

SORT

Product Availability
–

Show In Stock Only (18)

Review Score
–

(2)

Price Range
–

$5 to $10 (1)
$15 to $20 (1)
$20 to $25 (2)
$30 to $35 (3)
$35 to $40 (2)
$40 to $45 (4)
$45 to $50 (2)
$50 to $60 (2)
$60 to $70 (2)
$70 to $80 (6)

Lennox Cable Ties & Wiring Harnesses

Help Face
Need a little help?
50 items
Grid
List
Compare
Product Image of Rubber Plug, 10L24
Rubber Plug, 10L24
SKU: 10L24
Lennox
SKU: 10L24
Brand: Lennox
$8.99 each
Backorder
Get it by Mon, Dec 21 - Fri, Jan 22
Backorder
Get it by Mon, Dec 21 - Fri, Jan 22
Compare
Product Image of Wiring Harness, 49W87
Wiring Harness, 49W87
SKU: 49W87
Lennox
SKU: 49W87
Brand: Lennox
$67.39 each
Backorder
Get it by Mon, Dec 21 - Fri, Jan 22
Backorder
Get it by Mon, Dec 21 - Fri, Jan 22
Resources
FAQs, Manuals & Videos
Articles
More About Lennox Cable Ties & Wiring Harnesses

Lennox Cable Ties & Wiring Harnesses are the small electrical components that keep control wiring organized, secured, and protected inside a furnace, air handler, or condensing unit. A wiring harness bundles multiple pre terminated wires into a single connector, letting a technician replace a control board or blower motor without splicing individual wires one at a time. Cable ties, by comparison, are simple fasteners that route loose wiring away from moving parts, sharp sheet metal edges, and heat sources inside the cabinet.

Both parts are inexpensive on their own but critical to a safe, code compliant installation. Wiring left loose inside an HVAC cabinet can chafe against a panel edge over time, wearing through insulation and creating a short or an intermittent fault that is difficult to diagnose later. Stocking the correct OEM harness for a given model, rather than splicing a universal substitute, also keeps a repair matched to the equipment manufacturer's original wiring layout.

Subcategories

  • Molex Connector Harnesses: These pre terminated harnesses use a keyed multi pin connector common across many Lennox furnace and air handler control boards, allowing a fast plug in replacement without cutting or crimping wire.
  • Single Wire Harness Leads: Individual leads connect one component, such as a sensor or limit switch, back to the control board and are useful when only one wire in a larger harness has failed.
  • Cable Ties and Mounting Clips: Standard nylon ties and adhesive backed mounts secure loose wiring runs against cabinet panels, keeping harnesses away from the blower wheel and away from sharp sheet metal edges.
  • Ignition and Control Wiring Kits: These kits bundle the wiring specific to ignition control circuits, which see frequent heat exposure and benefit from replacement as a full set rather than one wire at a time.
  • Buying Guide

    Matching a harness to the exact equipment model is the first step, since Lennox has used different connector styles and pin counts across product generations. Pulling the model and serial number off the unit's rating plate before ordering avoids a mismatched connector that will not seat properly on the control board.

    Lennox Cable Ties & Wiring Harnesses cover both full harness assemblies and individual leads, so a technician diagnosing a single failed wire does not always need to replace the entire harness. Checking which specific circuit has failed, rather than assuming the whole assembly is bad, can save both time and cost on the call.

    Wire gauge and insulation rating matter most on harness sections that run near the burner or heat exchanger, where ordinary insulation can degrade faster than wiring routed through cooler parts of the cabinet. Choosing OEM replacement parts rated for that location keeps the repair as durable as the original build.

    For cable ties specifically, heat resistance is worth checking before buying in bulk for a service van. A standard tie used near a hot surface can soften and fail well before a heat rated version would, leading to a repeat callback.

    Finally, keeping a small stock of common Molex connector harnesses and assorted tie sizes on hand reduces trips back to a supply house mid job, since these are among the most frequently needed small parts across many Lennox service calls.

    Frequently Asked Questions

    What is the difference between a wiring harness and a single lead?

    A wiring harness bundles several pre terminated wires into one connector for a multi wire component swap, while a single lead is one wire meant to replace just one damaged connection. Choosing between them depends on how many circuits actually failed.

    Why does HVAC wiring need cable ties instead of just running loose?

    Loose wiring can chafe against sheet metal edges or contact the blower wheel over time, wearing through insulation and creating a short. Cable ties keep wiring bundled and away from moving or sharp parts inside the cabinet.

    How does a technician know which Molex harness fits a specific Lennox unit?

    The equipment's model and serial number on the rating plate is the most reliable reference, since connector style and pin count have changed across Lennox product generations. Matching against that number avoids ordering an incompatible part.

    Should heat rated cable ties be used near a furnace burner?

    Yes, standard ties can soften or fail when exposed to heat near a burner or heat exchanger, so a heat rated tie is the more reliable choice in that location.

    Is it better to replace a whole harness or just the damaged wire?

    If only one circuit has failed, replacing the single lead is usually faster and less costly. A full harness replacement makes more sense when several wires show wear or when the original harness is otherwise difficult to access.

Didn't find what you're looking for? 
Let us know
.