Apply to be a TradeMaster!
Filter menu expanded

Filters

2 items
Reset

SORT

Product Availability
–

Show In Stock Only (2)

Size
–

6" (1)
8" (1)

Price Range
–

$100 to $200 (2)

M Series Draft Controls

Help Face
Need a little help?
2 items
Grid
List
Compare
Product Image of 6" Draft Regulator for Wood, Oil, or Coal
$109.41 each
In Stock
Get 2 by Mon, Nov 23
In Stock
Get 2 by Mon, Nov 23
Compare
Product Image of 8" Draft Regulator for Wood, Oil, or Coal
$160.89 each
In Stock
Get 1 by Mon, Nov 23
In Stock
Get 1 by Mon, Nov 23
Resources
FAQs, Manuals & Videos
Other Resources
Articles
More About M Series Draft Controls

M Series Draft Controls regulate draft on oil, gas and solid fuel appliances. Field Controls builds the Type M+MG2 triple fuel draft control in diameters from 10 to 32 inches, and the control is CSA and cUL listed. The gate rests on a stainless steel knife edge supported by self-aligning bearings, a minimal-friction design that Field Controls says gives maximum sensitivity to draft changes. Installers use the M+MG2 on large residential, commercial and industrial equipment, including systems with 10-inch or larger vent pipe. The same control can serve gas appliances in place of a draft hood, and it can run as a single-acting unit on oil or solid fuel. Matching the fuel, acting configuration and diameter to the appliance is what makes the installation work, so those three details drive every purchase in this category.

Subcategories

  • Oil and Solid Fuel Applications: Single-acting M+MG2 installations are the option Field Controls lists for oil or solid fuel equipment. Boiler and furnace installers fit them to regulate draft on oil-fired and solid fuel units. The M+MG2 is cUL and CSA listed for oil, solid fuel and gas heating equipment. Diameters run from 10 to 32 inches, so the vent size sets the model.
  • Gas Appliance Applications: On gas appliances, Field Controls specifies the M+MG2 as an alternative to a draft hood. Installers use it on large gas-fired equipment with 10-inch or larger vent pipe. Field Controls includes a collar for secure installation.
  • Dual Fuel Oil and Gas Systems: The M+MG2 triple fuel design also serves dual fuel oil and gas systems. Contractors choose it for appliances that burn oil and gas and need draft regulation. The gate rests on a stainless steel knife edge with self-aligning bearings, which Field Controls designs for sensitivity to draft changes.

Buying Guide

Start with the fuel. The Type M+MG2 from Field Controls covers oil, gas and solid fuel, but the installation configuration changes with the fuel. Field Controls lists single-acting installations for oil or solid fuel and positions the control as an alternative to a draft hood on gas appliances. Dual fuel oil and gas systems are also a stated application. Confirm the appliance manufacturer's draft requirements before picking a configuration.

Next, size the control to the vent. The M+MG2 line runs from 10 to 32 inches in diameter and targets systems with 10-inch or larger vent pipe. Vent pipe smaller than 10 inches is not the stated application. Verify the vent diameter against the appliance documentation before ordering.

When comparing M Series Draft Controls, check the listings and build. The M+MG2 carries cUL and CSA listings and a stainless steel knife edge with self-aligning bearings for minimal friction. Field Controls includes a collar for installation.

Finally, consider the job. Field Controls designs the M+MG2 for large residential, commercial and industrial equipment, so confirm the control suits the boiler or furnace class before purchase. Consult the Type M+MG2 installation manual from the manufacturer for adjustment and mounting details. Working through fuel, configuration, diameter and listing in that order keeps the selection straightforward. Each step narrows the choice quickly.

Frequently Asked Questions

What do M Series Draft Controls regulate?

M Series Draft Controls like the Field Controls Type M+MG2 regulate draft on oil, gas and solid fuel appliances. The gate rests on a stainless steel knife edge with self-aligning bearings, which Field Controls says gives maximum sensitivity to draft changes. Installers use them on large residential, commercial and industrial equipment.

What sizes do M Series Draft Controls come in?

The Field Controls M+MG2 runs from 10 to 32 inches in diameter. The control is built for systems with 10-inch or larger vent pipe. Verify the diameter against the appliance documentation before ordering.

Can an M Series draft control replace a draft hood on a gas appliance?

Field Controls specifies the M+MG2 as an alternative to a draft hood on gas appliances. Confirm that the appliance manufacturer and local code allow the substitution. The M+MG2 is cUL and CSA listed for oil, solid fuel and gas heating equipment.

Are M Series Draft Controls single-acting or double-acting?

The Type M+MG2 is offered in single-acting or double-acting installation configurations. Field Controls lists single-acting installations for oil or solid fuel. The manufacturer's installation manual is the place to confirm the right configuration for a specific appliance.

What listings do M Series Draft Controls carry?

The Field Controls Type M+MG2 is cUL and CSA listed. The control is approved for oil, solid fuel and gas heating equipment. A collar is included for installation.

Didn't find what you're looking for? 
Let us know
.