Reznor Relay, Switch, Limit Controls cover the electrical safety and control components used on Reznor gas-fired unit heaters, including high-temperature limit switches, flame rollout switches, contactors, and relays. Contactors in the category are commonly rated 208/240V at 20A for switching heater blower motor loads. Many Reznor limit controls are factory set and non-adjustable, interrupting the electric supply to the gas valve once a fixed temperature threshold is reached, which protects the heat exchanger from overheating and stops burner operation if venting or airflow is restricted. Flame rollout switches add a second layer of protection by monitoring heat around the burner compartment and shutting down the unit if flames roll outside the combustion chamber. Technicians servicing commercial unit heaters in warehouses, garages, and manufacturing spaces rely on matching the exact Reznor part number and electrical rating when swapping a failed control, since a mismatched switch can leave a heater without proper safety cutoff. Stocking the right relay, switch, or limit control keeps gas-fired unit heaters operating safely through the heating season.
Subcategories
Buying Guide
Start by pulling the model and serial number off the Reznor unit heater's data plate, since limit controls, switches, and relays are matched to specific heater series and won't cross over between models without confirming the electrical rating. Match the reset type next. Auto-reset limit controls restore power once the heat exchanger cools, which suits heaters that see routine temperature swings, while a heater that keeps tripping the same switch needs a technician on site anyway, so a manual reset control forces that visit before restart. Confirm voltage and amperage on any contactor or relay before ordering. A 208/240V, 20A contactor handles a typical unit heater blower motor, but multi-heater installations or larger blower motors may call for a higher-rated part, and installing an undersized contactor risks a burned-out coil or a control that welds shut under load. Reznor Relay, Switch, Limit Controls purchases should also account for flame rollout protection, since a missing or bypassed rollout switch leaves a heater without its secondary overheat safeguard. Facilities running multiple Reznor unit heaters on one heating season benefit from keeping a spare limit switch and contactor on the shelf for each model in service, since a single tripped safety device can take a whole space offline until the correct replacement part arrives. Ordering by exact Reznor part number, rather than by general switch type, prevents a mismatch that could compromise the heater's built-in safety functions.
Frequently Asked Questions
What's the difference between an auto-reset and a manual-reset limit switch on a Reznor unit heater?
An auto-reset limit switch on a Reznor unit heater restores power to the gas valve automatically once the heat exchanger cools back below the setpoint. A manual-reset limit switch stays tripped until a technician presses a reset button, which forces a service visit before the heater restarts. Facilities with a history of nuisance overheating often use the manual-reset style so a live technician confirms airflow and venting before restart.
What amperage rating does a Reznor unit heater contactor need?
Reznor unit heater contactors are commonly rated 208/240V at 20A to match typical blower motor circuits. Larger unit heaters or multi-heater setups on a shared control board may need a higher-rated contactor. Checking the data plate on the unit heater before ordering keeps the replacement contactor matched to the original motor load.
Why did the flame rollout switch trip on a Reznor unit heater?
A flame rollout switch trips when flame escapes the combustion chamber instead of drawing up through the heat exchanger as designed. Common causes include a blocked flue, a cracked heat exchanger, or an inducer that isn't pulling enough draft. Resetting the switch without correcting the underlying airflow or venting problem risks a repeat trip and continued unsafe combustion.
Can a Reznor relay or limit control be swapped for a universal part?
Reznor relays, switches, and limit controls are matched to specific unit heater series, so voltage, amperage, and mounting pattern need to line up with the original part. A universal control might fit physically but run at the wrong rating for the motor or safety circuit it's protecting. Ordering by exact Reznor part number keeps the heater's built-in safety functions intact.
How often should limit switches and contactors be checked on a Reznor unit heater?
Limit switches and contactors on a Reznor unit heater are typically checked during scheduled heating-season startup and shutdown service visits. A technician tests that the high-temperature limit trips and resets correctly and inspects the contactor for pitted contacts or a chattering coil. Catching a worn contactor or a failing limit switch during routine service prevents an unexpected heater shutdown in the middle of winter.