Viega MANABLOC Caps are port and supply caps for MANABLOC manifold systems. The SupplyHouse listing includes the 36204 port cap for the discontinued 3/8 inch compression MANABLOC, the 36205 1/2 inch port cap, and the 53601 supply end cap. The 36205 fits all ports except 3/8 inch compression ports, and it's listed as plastic with a maximum of 200 psi and 200°F. SupplyHouse lists it as meeting NSF, ASTM F877, and ASTM F1960 standards. The 53601 is a supply end cap used on MANABLOC and MiniBloc manifold systems to cap an unused supply connection. The caps are described as safety caps for a port or supply connection that is not in use. Port caps and supply caps are different parts, so matching the cap to the connection type matters before the order goes in.
Subcategories
Buying Guide
Start by identifying the connection that needs capping. A MANABLOC manifold has port connections and supply connections, and each has its own cap. Port caps close an unused port, while a supply end cap closes an unused supply connection.
Next, check the port size and type. The 36205 is the 1/2 inch port cap and fits all ports except 3/8 inch compression ports. The 3/8 inch compression ports take the 36204, which is listed for the discontinued 3/8 inch compression MANABLOC. On an older compression manifold, confirm the port type before ordering.
Then check the ratings. SupplyHouse lists the 36205 as plastic with a maximum of 200 psi and 200°F. Material matters too: the 36205 is plastic, so check the system's operating temperature against its 200°F rating. Ratings belong to the model named, so check the product page for the 36204 and 53601 before assuming the same figures apply. The 36205 is also listed as meeting NSF, ASTM F877, and ASTM F1960 standards.
Finally, plan the whole order. When ordering Viega MANABLOC Caps for a job, count the unused ports and supply connections first. Note whether the manifold is a MANABLOC or a MiniBloc, since the 53601 is used on both systems. Counting unused connections early also avoids a short order and a second trip.
Frequently Asked Questions
What do Viega MANABLOC Caps do?
Viega MANABLOC Caps close off a port or supply connection on a MANABLOC manifold that isn't in use. Port caps handle unused ports, and the supply end cap handles an unused supply connection. SupplyHouse describes them as safety caps for unused connections.
Which MANABLOC port cap fits a 1/2 inch port?
The Viega 36205 is the 1/2 inch MANABLOC port cap in the Viega MANABLOC Caps listing. It fits all ports except 3/8 inch compression ports. For those ports, the 36204 is the listed cap.
What are the pressure and temperature ratings on the 36205 port cap?
SupplyHouse lists the Viega 36205 MANABLOC port cap at a maximum of 200 psi and 200°F, in plastic. The ratings apply to the 36205, so check the product page for other Viega MANABLOC Caps before assuming the same figures. It's also listed as meeting NSF, ASTM F877, and ASTM F1960 standards.
Is there a cap for the 3/8 inch compression MANABLOC?
Yes. The Viega 36204 is the lead free port cap listed for the discontinued 3/8 inch compression MANABLOC. The 36205 doesn't fit those 3/8 inch compression ports. Confirm the manifold's port type before ordering the right cap from the Viega MANABLOC Caps listing.
What cap do I use on an unused supply connection?
The Viega 53601 MANABLOC supply end cap is listed for capping an unused supply connection. It's used on MANABLOC and MiniBloc manifold systems. Viega MANABLOC Caps for supply connections are separate parts from the port caps.