Eemax Series Two Electric Tankless Heaters are commercial-grade point-of-use water heaters built for sinks, eyewash stations, and sanitation fixtures that need hot water without a storage tank. The line spans roughly 15 kW to 23 kW of heating capacity, sized to match the fixture count and flow demand of the application. Models carry either a TC or T2 suffix, and that designation determines both the heating module layout and the maximum flow rate the unit can support. Because the units mount directly on a wall near the point of use and eliminate the tank entirely, Series Two heaters free up mechanical room space that a storage tank system would otherwise require. Facilities managers specifying hot water for multiple lavatories, break room sinks, or eyewash stations need a heater that delivers consistent temperature without the recovery lag of a tank, and the thermostatic control built into this series addresses that directly.
Subcategories
Buying Guide
Specifying Eemax Series Two Electric Tankless Heaters starts with counting the fixtures the unit needs to serve simultaneously, since flow rate requirements multiply quickly once more than one tap opens at once. A single sink or eyewash station typically fits within a TC model's 3.0 gallon per minute rating, while a restroom core with several lavatories or a multi-user sanitation station calls for a T2 model rated up to 4.0 gallons per minute. Heating capacity in kilowatts should match available electrical service at the installation site, since the 15 kW to 23 kW range in this series draws meaningfully different amperage depending on the model chosen. Checking panel capacity and circuit sizing before ordering avoids a unit that cannot be wired as specified. Application type matters as much as flow and power. Eyewash stations and safety showers often call for a factory-set temperature model to meet regulatory expectations for eyewash safety equipment without relying on field adjustment, while general handwashing or break room sinks can use an adjustable thermostatic model. Space constraints near the point of use also factor into the decision, since these units mount on a wall and eliminate the footprint a storage tank would need, which matters in tight mechanical closets or under-counter installations. Reviewing the specification sheet for exact amperage, voltage, and wire gauge requirements before rough-in prevents a mismatch between the heater ordered and the electrical service already run to the location.
Frequently Asked Questions
What is the difference between TC and T2 models in the Eemax Series Two line?
TC models use staged heating modules and max out at 3.0 gallons per minute, while T2 models use parallel heating modules and support up to 4.0 gallons per minute. Staged heating brings capacity online incrementally, while parallel heating engages all modules together for faster response to sudden demand. Choosing between them comes down to how many fixtures the unit needs to serve at once.
What is the heating capacity range for Series Two tankless heaters?
Capacity across the Series Two line runs from roughly 15 kW up to 23 kW, depending on the specific model selected. Higher kW models support greater flow and faster temperature rise but draw correspondingly more amperage from the electrical panel. Confirming available electrical service before ordering keeps the installation straightforward.
Can Eemax Series Two heaters be used for eyewash stations?
Certain Series Two models ship with a factory-set temperature specifically intended for eyewash and emergency shower applications. A factory-set unit removes the need for field adjustment, which helps maintain the safe, consistent temperature these safety fixtures require. Facilities managers should confirm the specific model's intended application before installation.
Do Eemax Series Two heaters require a storage tank?
No. Series Two units are tankless, point-of-use electric water heaters that mount on a wall near the fixture they serve and heat water on demand. Eliminating the tank frees up mechanical room or under-counter space that a storage system would otherwise occupy. Hot water output starts as soon as the tap opens rather than waiting on tank recovery.
How many fixtures can one Eemax Series Two unit support?
Fixture count depends on the model's flow rating, with TC models supporting up to 3.0 gallons per minute and T2 models supporting up to 4.0 gallons per minute. A single sink or eyewash station typically works within a TC unit's capacity, while multiple lavatories or a sanitation station bank often requires a T2 model. Matching fixture count and expected simultaneous use to the flow rating keeps water temperature consistent under load.