HT450 Series pumps are high-temperature submersible sump pumps built for draining water that exceeds the limits of a standard sump pump. Each unit runs a 1/2 HP motor housed in cast aluminum with stainless steel fasteners and handles liquid up to 180 degrees Fahrenheit, so the pump keeps working where hot condensate, wash-down water, or process discharge would damage a standard plastic-bodied pump. A 1-1/2 inch discharge and 3/8 inch solids handling let the pump pass debris without clogging, while an oil-filled motor with thermal protection and permanently lubricated bearings keeps the unit running through repeated hot-water cycles. A high-temperature float mechanism triggers the pump automatically, so it operates unattended once wired into the pit. Commercial kitchens, laundries, and any application discharging hot wastewater into a sump depend on this heat tolerance, since a standard submersible pump would fail well before reaching 180 degrees.
Subcategories
Buying Guide
Selecting a high-temperature sump pump starts with confirming the water temperature the pump will actually see, since a standard sump pump is rated well below the 180 degree Fahrenheit ceiling this line is built for. Any application discharging hot condensate, wash-down water, or process rinse water into a sump pit needs that elevated rating, or the housing and seals will fail faster than expected. Next, check solids handling against what the pit actually collects; a 3/8 inch rating passes typical debris and food particulate but isn't a substitute for a grinder pump if the application involves heavier solids. The HT450 Series pairs that solids rating with a 1-1/2 inch discharge, so confirm the existing discharge piping matches before ordering to avoid adding a reducer or coupling on install day. Motor construction matters as much as horsepower here. An oil-filled motor with thermal protection and permanently lubricated bearings holds up better under continuous hot-water duty cycles than a standard air-filled motor, which is the main reason this construction differs from a general-purpose sump pump at the same horsepower. Housing material is also worth checking: cast aluminum sheds heat faster than plastic and pairs with stainless steel fasteners that resist corrosion in laundry, kitchen, and industrial water that's often treated with cleaning chemicals. Matching temperature rating, solids handling, and discharge size to the specific application prevents an early pump failure.
Frequently Asked Questions
What temperature water can an HT450 Series pump handle?
HT450 Series pumps handle liquid up to 180 degrees Fahrenheit, well above the rating of a standard submersible sump pump. The rating makes the pump suitable for condensate, wash-down water, and process rinse water that would damage standard plastic-bodied pumps. Checking the actual discharge temperature at the pit is still worth doing before installation, since some processes run hotter than expected.
What size solids can the HT450 Series pass?
The HT450 Series handles solids up to 3/8 inch, enough for typical debris and food particulate found in kitchen and laundry drain water. Heavier solids loads call for a grinder pump instead of this series. A 1-1/2 inch discharge works alongside the solids rating to keep flow moving without clogging.
Why does the HT450 Series use an oil-filled motor?
An oil-filled motor construction gives HT450 Series pumps thermal protection and permanently lubricated bearings, both suited to continuous duty in hot water applications. Facility teams running kitchens, laundries, or industrial process water rely on this construction to avoid the early motor failures common with standard air-filled pumps in the same conditions. The design also reduces how often bearings need manual maintenance.
What discharge size does the HT450 Series use?
HT450 Series pumps use a 1-1/2 inch discharge across the line, sized to handle higher-volume drainage from kitchens, laundries, and industrial sumps. Confirming that existing discharge piping matches this size before ordering avoids adding a reducer fitting during installation. The discharge size stays consistent regardless of the specific application the pump serves.
Where does an HT450 Series pump make more sense than a standard sump pump?
An HT450 Series pump makes sense anywhere water entering the pit regularly exceeds the temperature rating of a standard sump pump, since standard housings and seals degrade faster under sustained heat. Commercial kitchens, laundries, and industrial sites discharging hot process water into a sump pit are the typical applications. Cast aluminum construction and stainless steel fasteners add corrosion resistance in these same environments.