Apply to be a TradeMaster!
Filter menu expanded

Filters

3 items
Reset

SORT

Product Availability
–

Show In Stock Only (3)

Duct Size
–

4" (1)
6" (1)
8" (1)

Length (Inches)
–

7-5/8" (1)
11" (1)
5-1/8" (1)

Review Score
–

(1)
(1)

Price Range
–

$25 to $30 (2)
$30 to $35 (1)

Tamarack Backdraft Dampers

Help Face
Need a little help?
3 items
Grid
List
Compare
Product Image of 4" Cape Backdraft Damper
4" Cape Backdraft Damper
SKU: TTI-CBD4
Tamarack
SKU: TTI-CBD4
Brand: Tamarack
(8)
$27.54 each
In Stock
Get 148 by Mon, Nov 23
In Stock
Get 148 by Mon, Nov 23
Compare
Product Image of 6" Cape Backdraft Damper
6" Cape Backdraft Damper
SKU: TTI-CBD6
Tamarack
SKU: TTI-CBD6
Brand: Tamarack
(5)
$29.00 each
In Stock
Get 25 by Mon, Nov 23
In Stock
Get 25 by Mon, Nov 23
Compare
Product Image of 8" Cape Backdraft Damper
8" Cape Backdraft Damper
SKU: TTI-CBD8
Tamarack
SKU: TTI-CBD8
Brand: Tamarack
$31.50 each
In Stock
Get 10 by Mon, Nov 23
In Stock
Get 10 by Mon, Nov 23
Resources
FAQs, Manuals & Videos
Articles
More About Tamarack Backdraft Dampers

Tamarack Backdraft Dampers are fabric sleeve dampers built to stop outside air from entering bathroom, kitchen, and laundry exhaust ducts when the fan or dryer shuts off. The Cape Backdraft Damper line ships in four inch, five inch, six inch, and eight inch diameters, matching the round duct sizes most residential exhaust systems already use. A specially formulated fabric sleeve opens with almost no resistance while the appliance runs, then closes on its own once airflow stops, with no mechanical parts to stick, jam, or break. Contractors install these dampers on bathroom exhaust fans, clothes dryer vents, and kitchen range hoods to cut cold air infiltration and keep conditioned air from leaking out through an idle duct run. Every damper in the line ships with a lifetime warranty and is made in the USA. For a home performance contractor chasing air leaks, swapping in a fabric sleeve damper closes off one of the more overlooked sources of duct related drafts.

Subcategories

  • 4 Inch Cape Backdraft Dampers: The 4 inch Cape Backdraft Damper fits the small round duct runs typical of bathroom exhaust fans and some dryer vent installations. Installers slide the fabric sleeve unit inside the existing duct rather than replacing duct sections. A specially formulated sleeve opens under minimal fan pressure and closes once the fan shuts off. A lifetime warranty and made in USA construction cover this size along with the rest of the Cape line.
  • 5 Inch Cape Backdraft Dampers: The 5 inch Cape Backdraft Damper covers duct sizes that fall between the more common 4 inch and 6 inch options, often found on bathroom exhaust retrofits with nonstandard duct runs. Its fabric sleeve design has no mechanical parts to jam or break over years of daily cycling. Contractors use this size when an existing duct measures 5 inches and downsizing or upsizing the run isn't practical. Installation involves sliding the sleeve into the existing duct without cutting or resizing ductwork.
  • 6 Inch Cape Backdraft Dampers: The 6 inch Cape Backdraft Damper suits larger bathroom exhaust systems, whole house ventilation fans, and many clothes dryer exhaust runs. Its size handles higher airflow volumes than the smaller 4 inch option while keeping the same low resistance, fabric sleeve design. Contractors specify this size on kitchen range hood installations that call for annual inspection and cleaning per the manufacturer. Made in USA construction and a lifetime warranty apply across this size as well.
  • 8 Inch Cape Backdraft Dampers: The 8 inch Cape Backdraft Damper handles the largest duct runs in the Cape line, typically high capacity range hoods and larger mechanical ventilation systems. Higher airflow appliances need a damper that opens fully without restricting fan performance, and the fabric sleeve design scales up to this size without adding mechanical parts. Contractors installing kitchen range hood exhaust in commercial or high output residential kitchens commonly spec this size. Range hood installations using this damper size call for annual inspection and cleaning, per the manufacturer's guidance.

Buying Guide

Duct diameter drives the sizing decision on any backdraft damper purchase. Measure the actual round duct where the damper will sit, since the Cape line ships in four inch, five inch, six inch, and eight inch diameters, and a mismatched size either restricts airflow or fails to seat tightly enough to block outside air. Application matters just as much as size. Bathroom exhaust fans and typical dryer vents usually run four or five inch duct, while kitchen range hoods and higher capacity ventilation systems often need six or eight inch duct to move the required air volume. Tamarack Backdraft Dampers use a fabric sleeve design with no mechanical parts to jam or break, which matters on jobs where recurring callbacks for stuck dampers have been a problem. Installation location affects long term performance too. A damper installed too close to a duct elbow or transition can restrict the sleeve's ability to open fully, so a straight duct run at the install point improves performance. Range hood installations carry an added consideration: the manufacturer calls for annual inspection and cleaning on kitchen exhaust applications, since grease buildup affects any damper type over time. Warranty coverage is uniform across the line, with every size backed by a lifetime warranty and made in the USA, so warranty terms don't factor into the sizing or placement decision.

Frequently Asked Questions

What size backdraft damper fits a typical bathroom exhaust duct?

Most bathroom exhaust fans run 4 inch round duct, which matches the smallest size in the Cape Backdraft Damper line. Some installations use 5 inch or 6 inch duct instead, so measuring the existing duct before ordering avoids a mismatched fit. The Cape line covers 4, 5, 6, and 8 inch diameters to match the range of residential exhaust duct sizes.

Do these dampers have moving parts that wear out?

The Cape Backdraft Damper uses a fabric sleeve rather than a hinged mechanical flap, with no mechanical parts to jam or break over time. A specially formulated sleeve opens under fan pressure and closes on its own once airflow stops. A lifetime warranty backs the design across every size in the line.

Can a backdraft damper go on a kitchen range hood?

Cape Backdraft Dampers work on kitchen range hood exhaust in both the 6 inch and 8 inch sizes, matching the higher airflow volumes range hoods typically move. Grease buildup on any damper used in a range hood application makes annual inspection and cleaning necessary. Sizing the damper to the hood's actual duct diameter keeps airflow unrestricted.

Does the damper need extra duct sealing to work properly?

The Cape Backdraft Damper fits inside existing round duct without replacing duct sections, and the fabric sleeve seals against backflow using appliance airflow pressure alone. Proper function still depends on the surrounding duct being sized and sealed correctly, since a leaky or oversized duct run reduces the pressure the sleeve needs to close fully. Placing the damper away from elbows and transitions helps it open and close consistently.

Is the damper made for indoor or outdoor duct runs?

Cape Backdraft Dampers are built for exhaust duct applications like bathroom fans, clothes dryers, and kitchen range hoods, which typically terminate at an exterior wall or roof cap. A lifetime warranty and made in USA construction back the damper across the duct run leading to that termination point. Installation location within the duct, rather than indoor versus outdoor placement, determines correct sizing.

Didn't find what you're looking for? 
Let us know
.