TracPipe CSST Fittings are the mechanical connectors manufactured by OmegaFlex for joining TracPipe and TracPipe CounterStrike corrugated stainless steel tubing to appliances, meters, and rigid gas pipe. The AutoFlare fitting style is a self-piloting design that threads onto NPT connections without special tools or additional parts, which cuts down on assembly steps at each joint. CounterStrike tubing is sized the same as conventional TracPipe and uses the same AutoFlare and AutoSnap fitting families, so a crew stocking one fitting line can service either tubing type. The newer AutoSnap fitting attaches with a twist-and-snap motion and doesn't require disassembly or reassembly to connect to CounterStrike tubing. Gas installers rely on matching the correct fitting style and size to the tubing diameter at every transition point, from the meter to the appliance shutoff, since a mismatched fitting compromises the gas-tight seal. Selecting the right fitting family up front keeps a CSST gas piping installation consistent from end to end.
Subcategories
Buying Guide
Start by confirming whether the installation uses conventional TracPipe or TracPipe CounterStrike tubing, since both share the same fitting sizes and families even though the tubing itself differs in construction. Fitting style comes next: AutoFlare fittings handle transitions to standard NPT thread at appliances and manifolds without special tools, while AutoSnap fittings are built for faster field assembly on CounterStrike runs using a twist-and-snap connection. TracPipe CSST Fittings need to match the tubing diameter at every joint, so measure the tubing size before ordering rather than assuming a size based on the appliance's gas demand alone. At the meter connection, local code often requires a rigid stub-out section rather than flexible tubing terminating directly at the meter, so confirm that requirement with the authority having jurisdiction before finalizing a parts list. Branch points in a run call for a tee sized to match the main run, with reducing adapters available where a branch line steps down to a smaller diameter. Brass construction throughout the AutoFlare and AutoSnap lines holds up to the pressures and temperatures typical of residential and light commercial gas distribution. Ordering a complete fitting set, including straight adapters, tees, elbows, and stub-outs, before starting a job prevents a mid-installation parts run for a missing connector size. Keeping fitting style consistent across a single run also simplifies future service calls, since a technician won't need two different connection methods to service the same line.
Frequently Asked Questions
What's the difference between AutoFlare and AutoSnap TracPipe fittings?
AutoFlare fittings use a self-piloting thread design to connect CSST tubing to standard NPT-threaded connections without special tools. AutoSnap fittings connect to CounterStrike tubing with a twist, snap, and tighten motion that skips disassembly and reassembly. Both fitting families are manufactured by OmegaFlex and sized to match conventional TracPipe and CounterStrike tubing.
Do TracPipe CSST Fittings work with both TracPipe and CounterStrike tubing?
CounterStrike tubing is sized identically to conventional TracPipe, and the two products use the same AutoFlare and AutoSnap fitting families. A crew stocking one set of fittings can service either tubing type as long as the fitting size matches the tubing diameter. Checking tubing diameter before selecting a fitting avoids a mismatch at the joint.
What is a meter termination stub-out used for?
A meter termination stub-out transitions flexible CSST tubing to a fixed-length rigid pipe section at the gas meter connection. Many jurisdictions require this rigid section rather than allowing flexible tubing to terminate directly at the meter. Stub-outs are available in sizes matching common CSST diameters, including 1/2 inch and 3/4 inch.
Can TracPipe fittings be installed without special tools?
AutoFlare fittings are designed to thread onto NPT connections without special tools or additional parts. AutoSnap fittings go a step further, connecting to CounterStrike tubing with a twist-and-snap motion that can be completed while wearing work gloves. Both designs reduce the number of loose parts handled during installation.
How does a branch connection work on a TracPipe CSST run?
A brass tee, sized to match the tubing diameter, allows a single CSST run to branch and feed a second appliance. Reducing adapters are available where a branch line needs to step down to a smaller tubing diameter. Matching tee and adapter sizes to the actual tubing run keeps every joint gas-tight.