'/%3E%3C/svg%3E)
1-1/4" AquaPEX White - (300 ft. coil)
 --%3E %3Csvg version='1.1' id='Fill' xmlns='http://www.w3.org/2000/svg' xmlns:xlink='http://www.w3.org/1999/xlink' x='0px' y='0px' viewBox='0 0 100 100' enable-background='new 0 0 100 100' xml:space='preserve'%3E %3Cpath fill='%23F15C02' d='M79.44,0.95H20.56C9.78,0.95,0.95,9.78,0.95,20.56v58.87c0,10.79,8.82,19.61,19.61,19.61h58.87 c10.79,0,19.61-8.83,19.61-19.61V20.56C99.05,9.78,90.22,0.95,79.44,0.95z M65.38,58.24l9.38,29.58L49.69,69.78L24.5,87.82 l9.34-29.6L8.8,39.6l30.73-0.17c0,0,6.98-19.61,10-28.93c0.54,1.36,9.88,29.1,9.88,29.1H91.2L65.38,58.24z'/%3E %3C/svg%3E){kind=small}
MANUALS (6)
Lift Gate
Product Highlights
Description
Uponor AquaPEX is manufactured and listed to ASTM F876 and F877 and certified to NSF Standards 14 and 61. Uponor AquaPEX tubing is rated and listed by the Hydrostatic Stress Board of PPI at 200 degrees F at 80 psi, 180 degrees F at 100 psi and 73.4 degrees F at 160 psi.
Note: Uponor 1/2" AquaPEX tubing is listed to UL1821 and ULC/ORD C199 P and carries an additional rating of 120 degrees F at 130 psi.
What are the Uponor PEX standards?
Uponor PEX and associated fittings are manufactured to the following standards:
- ASTM F876 "Standard Specification for Cross-linked Polyethylene (PEX) Tubing"
- ASTM F877 "Standard Specification for Cross-linked Polyethylene (PEX) Plastic Hot and Cold Water Distribution Systems"
- ASTM F1960 "Standard Specifications for Cold Expansion Fittings with PEX Reinforcing Rings for use with Cross-linked Polyethylene (PEX) Tubing"
- ASTM F2080 "Standard Specifications for Cold Expansion Fittings with Metal Compression Sleeves for Cross-linked Polyethylene (PEX) Tubing"
- CSA B137.5 Thermoplastic Pressure Piping Compendium
- ANSI/NSF Standard 14 "Plastics Piping System Components and Related Materials"
- ANSI/NSF Standard 61 "Drinking Water System Components - Health Effects"
- UL 1821 "Standard for Safety for Thermoplastic Sprinkler Pipe and Fittings for Fire Protection Service" (1/2" Uponor AquaPEX only)
Uponor AquaPEX tubing is approved in the following codes:
- IPC
- UPC
- NSP
- IMC
- UMC
- NSPC
- NPC of Canada
- NBC of Canada
Uponor AquaPEX tubing has the following listings:
- IAPMO
- NSF
- CSA
- ITS
- HUD
- ICC
- G573 - Two-hour Hambro floor/ceiling assembly
- K913 - Two-hour concrete floor/ceiling assembly
- L557 - One-hour wood frame floor/ceiling assembly
- U372 - One-hour wood frame wall assembly
- V444 - One-hour steel stud wall assembly
Specs
| Length (Feet): | 300' |
|---|---|
| Fitting System Compatibility: | PEX Press Push Fit Crimp Clamp PEX Compression Expansion PEX |
| Size: | 1-1/4" |
| Shape: | Coil Coil |
| Tubing Type: | Non-Oxygen Barrier |
| Material: | PEX |
| Color: | White |
| Application: | Plumbing |
| Max Pressure (PSI): | 160 |
| Grade: | PEX-a |
| Warranty: | 25 Year |
| Standards Met: | ASTM F877 DIN4726 NSF |
| Max Temp (F): | 200°F |
Contact
Happy Independence Day!
You May Also Need
Product Reviews
Most Liked Positive Review
Can't Go Wrong
Most Liked Negative Review
 --%3E %3Csvg version='1.1' id='With-RB' xmlns='http://www.w3.org/2000/svg' xmlns:xlink='http://www.w3.org/1999/xlink' x='0px' y='0px' viewBox='0 0 100 100' enable-background='new 0 0 100 100' xml:space='preserve'%3E %3Cpath fill='%23FBC8B4' d='M79.44,0.95H20.56C9.78,0.95,0.95,9.78,0.95,20.56v58.87c0,10.79,8.82,19.61,19.61,19.61h58.87 c10.79,0,19.61-8.83,19.61-19.61V20.56C99.05,9.78,90.22,0.95,79.44,0.95z M65.38,58.24l9.38,29.58L49.69,69.78L24.5,87.82 l9.34-29.6L8.8,39.6l30.73-0.17c0,0,6.98-19.61,10-28.93c0.54,1.36,9.88,29.1,9.88,29.1H91.2L65.38,58.24z'/%3E %3C/svg%3E){kind=small}
shipping wrap
Product arrived quickly and worked well
All the products are exceptional, would buy all the products
It's pex it works
Top Shelf.
Yes
PEX-A Pipe
Pex A is easy to work with.
This seems more flexible to me. I welcome that in tight
I would buy this product again and again
Great Service
Product Q&A
100 QuestionsQ: i need 1 inch aquapex at 300 ft but need to know. can it go underground 4 feet deep from well house to actual house?
Asked by rob 14 years ago
Add your answer
Verified Reply- PexSupply StaffAquaPEX tubing is approved for direct burial, but it's always a good idea to bury it below the frost line to prevent water from freezing in the lines. Information regarding the depth of the frost line in your area can normally be obtained from your water company or municipality.
Q: i would like to know how much a 300' 2" pex hose would weigh when full with water i need to run all 300'of it across a cieling with hangers any thoughts
Asked by 14 years ago
Add your answer
Verified Reply- PexSupply StaffWe can tell you that the 300-foot coil of 2" AquaPEX weighs 204.6 pounds without any water inside.
Area of a circle is pi*r^2. for a 2 inch pipe the radius is 1 inch. Therefore the cross section area is 3.14159 square inches. Multiply that by 300ft (in inches - 300*12)=11309.7 cubic inches =48.96 gallons (divide by 231). each gallon weighs 8.35 pounds for a total of 408.8 pounds (water only - add pipe weight). Therefore the hangers will have to support about 20 pounds each assuming they are attached every 10 feet.
My last answer assumed that the ID was 2". I found a site that shows it to be 1.629". Total weight of water S/B 272 lbs.
Q: Can I use 1-1/4" Aquapex in a water well installation? Would like to connect submersible pump to pitless adapter with Aquapex.
Asked by alaskawild 14 years ago
Add your answer
Verified Reply- PexSupply StaffYou can use AquaPEX in a water well installation, and it is approved for direct burial. You'll need to use appropriate PEX fittings to make any connections.
Q: Can aquapex be connected using the sharkbite or gatorbite fittings?
Asked by Tim 14 years ago
Add your answer
Verified Reply- PexSupply StaffYes. While AquaPEX is compatible with expansion-style PEX fittings, it also works with standard PEX fittings (including SharkBite and push-fit type fittings).
Q: I do not want to replace all the pipe to some fixtures. Is it ok to have a run of pex a and then leave the copper going to the fixtures? In other words intermix pex with copper? Replace the main 3/4 inch line with pex and leave the supply lines that are in the walls as they are, copper?
Asked by Rob 14 years ago
Add your answer
Verified Reply- PexSupply StaffThis would be fine and would probably save you some work. You'd just need to adapt the PEX to the copper with an appropriate fitting.
Q: Does the 3/8 aquapex come in blue and red? If I use 3/8 instead of 1/2 tubing to a bathroom sink, will there be a noticeable pressure difference?
Asked by 14 years ago
Add your answer
Verified Reply- PexSupply Staff3/8" AquaPEX is only available in white (in 400-ft. and 1,000-ft. coils). 3/8" is sufficient to supply sinks, but you'll want to run 1/2" to your showers.
Q: Can I us Aquapex to plumb into baseboard hot water heaters. The water will be heated by a oil fired furnance.
Asked by Robert 15 years ago
Add your answer
Verified Reply- PexSupply StaffAquaPEX is not recommended for use is closed heating systems. PEX without an oxygen barrier will allow oxygen from the air to penetrate the tubing. This will cause any ferrous metals in the system (mainly cast iron) to rust.
Q: how heavy is a 350 foot coil of 3 inch pex tubing and how large in diameter i have worked with one inch pex and the memory is strong how would you control or straighten three inch?!
Asked by 15 years ago
Add your answer
Verified Reply- PexSupply Staff3" AquaPEX has a 2.4" inside diameter and a 3.125" outside diameter. The 350-foot coil weighs 442 lbs. It would be difficult to install 3" PEX without the use of some type of commercial machinery.
Q: I plan to replace the galvanized pipes in the basement. Should I be concerned about UV rays coming though the basement windows affecting the pex tubing?
Asked by Kadex 15 years ago
Add your answer
Verified Reply- PexSupply StaffYou would only need to be concerned if the windows are not UV-resistant and the PEX gets exposed to consistent sunlight through those windows.
You are correct in the PEX cannot be used in any location exposed to UV radiation. most modern windows are UV blocking, so indoor exposure is not a problem.
Q: I am 17 years of age and have been doing plumbing for a good amount of time now i was wondering im doing a big job replacing all water and dwv pipes in the house what size pex would i use for the home?
Asked by Brad 15 years ago
Add your answer
Verified Reply- PexSupply Staff1/2" PEX is the standard size of lines feeding the fixtures. 3/8" is usually sufficient for sinks and toilets, but it is usually more difficult to find parts in this size. Supply lines are typically 3/4".
In general, you should use the same diameter pex as the existing water and dwv pipes.