Balanced Valve Regulators are gas pressure regulators built with a balanced valve design that holds outlet pressure steady even as inlet pressure swings. Maxitrol manufactures the balanced valve regulators carried at SupplyHouse, including the 210 Series and the R and RS Series. The 210 Series uses a lock-up design suited to gas-fired boilers, steam generators, industrial furnaces, and similar high-demand equipment, with NPT sizes running from 1 inch through 3 inches and flanged connections at 4 inches. A 2 inch model in that series, the 210E-2, carries a rating of 12,000,000 BTU. The R and RS Series relies on a double diaphragm balanced valve design that keeps outlet pressure steady across a wide swing in inlet pressure, and covers pipe sizes from 3/8 inch to 1 inch for main burner and pilot load applications. Picking the correct series and size keeps downstream equipment running at the pressure it was designed for, which protects burners, pilots, and combustion components from drift caused by upstream pressure changes.
Subcategories
Buying Guide
Start with the appliance's BTU input rating, since that number drives regulator sizing more than pipe size alone. An undersized regulator restricts gas flow to the burner and starves it during peak demand, while an oversized regulator can leave outlet pressure unstable at low firing rates. Match the connection size to the existing gas train: NPT threaded connections cover smaller residential and light commercial jobs, while flanged connections handle the large-diameter mains found on industrial boiler plants and multi-unit furnace rooms.
Next, weigh how much inlet pressure swings on the job site. Utility supply pressure can vary across a day, and a double diaphragm balanced valve design in the R and RS Series holds outlet pressure steadier than a single diaphragm design when that swing is wide. For high-demand equipment such as boilers, steam generators, and industrial furnaces, the 210 Series lock-up design adds a shutoff function that a straightforward main burner regulator does not.
Selecting Balanced Valve Regulators also means checking the outlet pressure range against what the burner manufacturer specifies, since running outside that range voids most burner warranties. Confirm pipe size, BTU rating, and outlet pressure range against the equipment nameplate before ordering, and keep the appliance manual on hand during commissioning so outlet pressure can be checked against the manufacturer's target once the regulator is installed.
Frequently Asked Questions
What is a balanced valve design in a gas regulator?
A balanced valve design routes a portion of upstream gas pressure to act on the downstream side of the valve plug, so pressure on both sides stays equal as inlet conditions change. Balanced Valve Regulators built this way hold outlet pressure steadier than unbalanced designs when supply pressure fluctuates. Maxitrol uses this design across both the 210 Series and the R and RS Series.
What size Balanced Valve Regulator does a gas-fired boiler need?
Sizing starts with the boiler's BTU input rating rather than the existing pipe size. The 210 Series covers NPT sizes from 1 inch to 3 inch plus a 4 inch flanged option, with the 210E-2 rated for 12,000,000 BTU and the 210J rated for 50,000,000 BTU. Checking the boiler nameplate against these ratings avoids under sizing or over sizing the regulator.
What's the difference between the 210 Series and the R and RS Series?
The 210 Series is a lock-up type regulator built for high-demand equipment such as boilers, steam generators, and industrial furnaces, covering sizes from 1 inch NPT to 4 inch flanged. The R and RS Series uses a double diaphragm balanced valve design in smaller pipe sizes from 3/8 inch to 1 inch, aimed at main burner and pilot load applications like infrared heaters. Job type and connection size usually decide which series fits.
Can a Balanced Valve Regulator handle wide swings in gas supply pressure?
The double diaphragm design in the R and RS Series is built specifically to hold steady outlet pressure across a wide range of inlet pressure. That stability matters most on pilot lines and infrared heater circuits, where a pressure spike can affect flame quality. Confirming the inlet pressure range on the job against the regulator's rated range prevents problems before startup.
What connection type do large industrial gas regulators use?
Regulators sized for the largest industrial loads typically move from threaded NPT connections to flanged connections. The 210J model uses a 4 inch flanged connection rated for 50,000,000 BTU, built for industrial boiler plants and multi-unit furnace rooms running large-diameter gas mains. Flanged connections also simplify future maintenance on large pipe runs.