PVC DWV Test Tees are fittings installed in drain, waste, and vent piping to allow pressure or water testing of a system before it gets covered by walls or slab. SupplyHouse stocks Holdrite TESTRITE and Spears models ranging from 2 inch through 12 inch sizes, each shipping with a cleanout plug for sealing the tee after testing wraps up. Sizes at 2 inch and 3 inch carry a pressure rating up to 50 feet of water head or 5 psi of air, while 4 inch and 6 inch sizes are rated up to 40 feet of head. Plumbers install these tees to satisfy horizontal and vertical testing requirements during rough-in inspections, since most plumbing codes require a documented pressure or water test before a DWV system gets buried or enclosed. Holdrite's TESTRITE line is made in the USA, lab tested, and IAPMO listed under both UPC and IPC standards. Choosing the correct size and pressure rating for the piping run keeps an inspection moving without a failed test or a fitting rated below what the job requires.
Subcategories
Buying Guide
Start with the pipe diameter already in the ground or wall. Test tees need to match the stack or branch size exactly, so confirming the diameter before ordering avoids a fitting that doesn't align with the rest of the DWV run. Holdrite covers 2 inch through 6 inch sizes, while Spears extends the range up to 12 inch for larger commercial mains.
Pressure rating matters just as much as size. Smaller 2 inch and 3 inch PVC DWV Test Tees carry a rating up to 50 feet of water head or 5 psi of air, while 4 inch and 6 inch sizes step down to 40 feet of head. Checking the local code requirement for test pressure against the fitting's rating before rough-in inspection prevents a failed test caused by an undersized fitting.
Testing orientation also factors into fitting selection, since these tees support both horizontal and vertical installation. Confirming the tee works for the specific run orientation on the job, whether a horizontal branch or a vertical stack, keeps the testing setup straightforward without needing extra fittings to reorient the assembly.
Complete kits that include a spanner ring and cleanout plug alongside the tee simplify the purchase, since everything needed for testing and future cleanout access comes in one package. Confirming a listing like IAPMO under UPC or IPC standards, where required by local code, also helps the fitting pass inspection without added scrutiny.
Frequently Asked Questions
What sizes do PVC DWV test tees come in?
PVC DWV Test Tees range from 2 inch through 12 inch diameters across the Holdrite TESTRITE and Spears lines. Holdrite covers 2 inch, 3 inch, 4 inch, and 6 inch sizes, while Spears extends coverage up to 8 inch, 10 inch, and 12 inch for larger commercial mains. Matching the tee diameter to the existing stack or branch size keeps the fitting properly aligned with the rest of the run.
What pressure rating do these test tees carry?
Test tees in 2 inch and 3 inch sizes carry a rating up to 50 feet of water head or 5 psi of air. Larger 4 inch and 6 inch sizes step down to a rating of 40 feet of head. Checking the local code requirement against the fitting's rating before rough-in inspection helps avoid a failed pressure test.
Can PVC DWV test tees be installed vertically?
PVC DWV Test Tees support both horizontal and vertical installation, covering branch lines as well as vertical stacks. Confirming the orientation needed for a specific run before ordering keeps the testing setup straightforward. Plumbers use the same tee design for either orientation without needing a different fitting.
What comes included with a test tee kit?
Complete test tee kits from Holdrite's TESTRITE line include the PVC test tee, a spanner ring, and a cleanout plug in one package. The spanner ring helps tighten the plug securely after the test wraps up. Having all three components together saves an extra trip to source a separate plug or ring.
Are these test tees code listed for inspection purposes?
Holdrite's TESTRITE PVC DWV Test Tees are IAPMO listed under both UPC and IPC standards, lab tested, and made in the USA. The listing helps the fitting pass inspection where local code requires a recognized certification. Confirming the specific listing required in a given jurisdiction before ordering keeps the rough-in inspection moving smoothly.