Plastic Insulation Coupling Strut Clamps are couplings that mount insulated pipe directly to strut channel, combining the function of a pipe clamp and an insulation shield into one part that snaps into place without additional metal hardware. HoldRite's lineup covers pipe sizes from 1/2 inch to 2 inch, available in both 1/2 inch and 1 inch insulation thickness options to match whatever wrap is already on the line. Each coupling meets the 25/50 flame spread and smoke developed index commonly referenced on plenum applications, a rating inspectors check on jobs running through return air plenums. Contractors use these couplings on trapeze hangers, single strut runs, and horizontal installations throughout a mechanical room, keeping the same part number in play across plenum support and standard insulated pipe support alike. Because the coupling combines the clamp and insulation shield into a single molded plastic part, it snaps directly into channel without the extra hardware a standard clamp and shield setup requires, which speeds up installation on runs with many support points.
Subcategories
Buying Guide
Match the coupling to the insulation thickness already on the pipe before checking pipe size. HoldRite's plastic strut clamps come in 1/2 inch and 1 inch insulation thickness options, and using the wrong thickness either crushes thinner insulation or leaves a gap around thicker wrap at the support point. Pipe size is the next spec, and it needs to be checked against the outer diameter of the pipe plus its insulation, not the bare pipe size. The lineup covers 1/2 inch to 2 inch pipe, with more part numbers concentrated in the smaller sizes since branch lines make up most of a typical mechanical room's insulated piping. Plastic Insulation Coupling Strut Clamps also carry a 25/50 flame spread and smoke developed rating, worth confirming against the project's mechanical specification before ordering since some jobs reference that rating specifically for plenum-rated installations. Mounting style matters too, and confirming the strut channel size already installed on the job avoids a mismatch, since the coupling snaps into a specific channel profile rather than fitting universally. Order a small buffer of extra couplings past what the takeoff calls for, since field conditions on a mechanical room ceiling rarely match the drawing exactly, and running short on a finished insulated run means either an uninsulated support point or a return trip to the supply house. Confirming both insulation thickness and pipe size against the actual installed pipe, rather than the drawing alone, remains the most reliable way to avoid an ordering mismatch.
Frequently Asked Questions
What insulation thickness options are available for plastic strut clamps?
HoldRite's plastic insulation coupling strut clamps come in 1/2 inch and 1 inch insulation thickness options to match whatever wrap is already on the pipe. Using the wrong thickness either crushes thinner insulation or leaves a gap at the support point. Checking the insulation thickness already installed before ordering avoids a mismatch.
What pipe sizes do plastic insulation coupling strut clamps cover?
The lineup covers pipe sizes from 1/2 inch to 2 inch, with sizing based on the outer diameter of the pipe plus its insulation rather than the bare pipe size. Smaller sizes make up most of a typical mechanical room's branch piping, while the larger 1-1/2 inch and 2 inch sizes cover mains and bigger branch runs. Measuring over the finished, insulated pipe before ordering keeps the size correct.
Do these couplings meet plenum rating requirements?
Yes, HoldRite's plastic insulation coupling strut clamps meet a 25/50 flame spread and smoke developed index, a rating commonly referenced on plenum applications. Confirming that rating against the project's mechanical specification is worth doing before ordering on any job running through a return air plenum. The same rating applies across the full plastic coupling lineup.
How do plastic insulation coupling strut clamps mount to pipe?
Plastic insulation coupling strut clamps combine the function of a pipe clamp and an insulation shield into a single molded plastic part that snaps directly into strut channel. That design skips the extra hardware a standard clamp and separate insulation shield setup requires. Installation works the same way across every pipe size and insulation thickness in the lineup.
Can plastic insulation coupling strut clamps be used on both trapeze and single strut supports?
Yes, these couplings are built for trapeze hangers, single strut runs, and horizontal installations throughout a mechanical room. The same part number works across plenum support and standard insulated pipe support applications. Confirming the strut size on the job matches the coupling's mounting design is still worth checking before ordering.