'/%3E%3C/svg%3E)
1-1/2" AquaPEX White - (300 ft. coil)
 --%3E %3Csvg version='1.1' id='Fill' xmlns='http://www.w3.org/2000/svg' xmlns:xlink='http://www.w3.org/1999/xlink' x='0px' y='0px' viewBox='0 0 100 100' enable-background='new 0 0 100 100' xml:space='preserve'%3E %3Cpath fill='%23F15C02' d='M79.44,0.95H20.56C9.78,0.95,0.95,9.78,0.95,20.56v58.87c0,10.79,8.82,19.61,19.61,19.61h58.87 c10.79,0,19.61-8.83,19.61-19.61V20.56C99.05,9.78,90.22,0.95,79.44,0.95z M65.38,58.24l9.38,29.58L49.69,69.78L24.5,87.82 l9.34-29.6L8.8,39.6l30.73-0.17c0,0,6.98-19.61,10-28.93c0.54,1.36,9.88,29.1,9.88,29.1H91.2L65.38,58.24z'/%3E %3C/svg%3E){kind=small}
MANUALS (6)
Lift Gate
Product Highlights
Description
Uponor AquaPEX is manufactured and listed to ASTM F876 and F877 and certified to NSF Standards 14 and 61. Uponor AquaPEX tubing is rated and listed by the Hydrostatic Stress Board of PPI at 200 degrees F at 80 psi, 180 degrees F at 100 psi and 73.4 degrees F at 160 psi.
Note: Uponor 1/2" AquaPEX tubing is listed to UL1821 and ULC/ORD C199 P and carries an additional rating of 120 degrees F at 130 psi.
What are the Uponor PEX standards?
Uponor PEX and associated fittings are manufactured to the following standards:
- ASTM F876 "Standard Specification for Cross-linked Polyethylene (PEX) Tubing"
- ASTM F877 "Standard Specification for Cross-linked Polyethylene (PEX) Plastic Hot and Cold Water Distribution Systems"
- ASTM F1960 "Standard Specifications for Cold Expansion Fittings with PEX Reinforcing Rings for use with Cross-linked Polyethylene (PEX) Tubing"
- ASTM F2080 "Standard Specifications for Cold Expansion Fittings with Metal Compression Sleeves for Cross-linked Polyethylene (PEX) Tubing"
- CSA B137.5 Thermoplastic Pressure Piping Compendium
- ANSI/NSF Standard 14 "Plastics Piping System Components and Related Materials"
- ANSI/NSF Standard 61 "Drinking Water System Components - Health Effects"
- UL 1821 "Standard for Safety for Thermoplastic Sprinkler Pipe and Fittings for Fire Protection Service" (1/2" Uponor AquaPEX only)
Uponor AquaPEX tubing is approved in the following codes:
- IPC
- UPC
- NSP
- IMC
- UMC
- NSPC
- NPC of Canada
- NBC of Canada
Uponor AquaPEX tubing has the following listings:
- IAPMO
- NSF
- CSA
- ITS
- HUD
- ICC
- G573 - Two-hour Hambro floor/ceiling assembly
- K913 - Two-hour concrete floor/ceiling assembly
- L557 - One-hour wood frame floor/ceiling assembly
- U372 - One-hour wood frame wall assembly
- V444 - One-hour steel stud wall assembly
Specs
| Length (Feet): | 300' |
|---|---|
| Fitting System Compatibility: | Expansion PEX Crimp Clamp PEX Compression PEX Press Push Fit |
| Size: | 1-1/2" |
| Shape: | Coil |
| Tubing Type: | Non-Oxygen Barrier |
| Material: | PEX |
| Color: | White |
| Application: | Plumbing |
| Max Pressure (PSI): | 160 |
| Grade: | PEX-a |
| Warranty: | 25 Year |
| Standards Met: | ASTM F877 NSF DIN4726 |
| Max Temp (F): | 200°F |
Contact
Happy Independence Day!
You May Also Need
Product Reviews
Most Liked Positive Review
Can't Go Wrong
Most Liked Negative Review
 --%3E %3Csvg version='1.1' id='With-RB' xmlns='http://www.w3.org/2000/svg' xmlns:xlink='http://www.w3.org/1999/xlink' x='0px' y='0px' viewBox='0 0 100 100' enable-background='new 0 0 100 100' xml:space='preserve'%3E %3Cpath fill='%23FBC8B4' d='M79.44,0.95H20.56C9.78,0.95,0.95,9.78,0.95,20.56v58.87c0,10.79,8.82,19.61,19.61,19.61h58.87 c10.79,0,19.61-8.83,19.61-19.61V20.56C99.05,9.78,90.22,0.95,79.44,0.95z M65.38,58.24l9.38,29.58L49.69,69.78L24.5,87.82 l9.34-29.6L8.8,39.6l30.73-0.17c0,0,6.98-19.61,10-28.93c0.54,1.36,9.88,29.1,9.88,29.1H91.2L65.38,58.24z'/%3E %3C/svg%3E){kind=small}
shipping wrap
Product arrived quickly and worked well
All the products are exceptional, would buy all the products
It's pex it works
Top Shelf.
Yes
PEX-A Pipe
Pex A is easy to work with.
This seems more flexible to me. I welcome that in tight
I would buy this product again and again
Great Service
Product Q&A
100 QuestionsQ: I have a house 2 years old and this Wirsbo Aquapex was used for my water supply system. I am told that I will have to expand the joints and use Wirsbo's own fitting system if I want to change anything. Is this true or can I use copper crimp rings and any standard 1/2" fittings?
Asked by Finishing My Basement 16 years ago
Add your answer
Verified Reply- PexSupply StaffUponor Wirsbo recommends using it's Propex expander system with Aquapex for warranty reasons. However, this tubing will work with other fitting systems such as crimp rings and crimp fittings.
Q: What is the typical radius for a 90 degree bend? (3/4" aquapex)
Asked by ron51 16 years ago
Add your answer
Verified Reply- PexSupply StaffThe minimum bending radius, or tightest you can get the tubing, would be 6 times the outside diameter of the tubing. This would equal 6 x .875", or 5.25". Typical radius would be from this amount to 8".
Ron, Most of my bends were about an 18" radius, with a minimal amount of effort. Sean
Q: Can you use shark bite fittings with this tubing?
Asked by 16 years ago
Add your answer
Verified Reply- PexSupply StaffYes, SharkBite fittings are compatible with this tubing.
Q: I am looking to install a 1 inch water line in an older building for an industrial laundry am I making a good choice with PEX and how flexable is it?
Asked by LT 16 years ago
Add your answer
Verified Reply- PexSupply StaffPEX is a good choice for this application because it is much easier to work with and less expensive than copper.
Q: Can I use stainless steel hydropex clamps with this tubing?
Asked by RBT 16 years ago
Add your answer
Verified Reply- PexSupply StaffYes, you would be able to use the stainless steel HydroPEX clamps to make connections with this tubing.
Q: We are looking to install additional baseboard heating units and are thinking of using PEX to connect to the other zones in the house. The rest of the heating zones are all copper tubing and the boiler temp could go to 180 F. Please let us know if this will work. Thanks
Asked by JRM 16 years ago
Add your answer
Verified Reply- PexSupply StaffYou would need to use an oxygen barrier tubing, such as thermaPEX or hePEX tubing.
Q: is this pex a?
Asked by 16 years ago
Add your answer
Verified Reply- PexSupply StaffYes this is PEX A grade tubing.
Q: Is this red pex paintable - we will have hot and cold water running to an outdoor shower?
Asked by Andy 16 years ago
Add your answer
Verified Reply- PexSupply StaffNo, the PEX tubing cannot be painted, however, we do offer blue PEX tubing and white PEX tubing. The tubing can be found by clicking on the link below: http://www.pexsupply.com/PEX-Tubing-516000
Q: Can we use pex tubing under ground and if so what kind is the best.
Asked by To to 16 years ago
Add your answer
Verified Reply- PexSupply StaffPEX tubing can be buried underground or in concrete. AquaPEX is our highest quality tubing; it is a grade A tubing, classified by the process used to produce the bonds between the molecules in the tubing. It is more flexible than other grades of tubing and is able to return to form after expanding due to freezing water or use of the Expansion fitting system.
PEX has thicker walls, making the inside diameter of the pipe smaller and less gallons per minute can travel through the pipe. I recommend 3/4" pipe when there are 2 bathrooms or less, 3 or more bathrooms use 1" PEX. Don't forget that some Metro Water companies like copper run out of the meter box about 4' before connecting to PEX. Since PEX is not detected with a metal detector, run a metal Water Warning Tape or a copper wire 6" to 10" below the surface of the ground. If you remove an old galvanized water pipe that is usually being used as the electrical ground, you must drive a new 8' grounding rod straight down into the ground outside and run a new grounded wire or extend the old one to the rod. Your best bet is to run the PEX through a new hole in the foundation and leave the old waterline in the ground. Some plumbers argue that the PEX will act as a ground of you connect the ground to a copper pipe that runs to the PEX, but they are WRONG! ASK AN ELECTRICIAN! BE SAFE!
Q: What is the maximum recommended run length from manifold to end fixture for 1/2" (and 3/4") Aquapex tubing?
Asked by Kris 16 years ago
Add your answer
Verified Reply- PexSupply StaffThe answer to this question will depend upon the incoming water pressure to your home, and the required water pressure at your fixture. Each application is unique. By considering incoming pressure and pressure loss, you can get a general idea of how long the run can be.