Z-Vent Tees are the fittings that connect horizontal and vertical sections of a Z-Flex Z-Vent gas vent system. The double wall Z-Vent system is designed for Category II, III, and IV heating equipment, including boilers, high efficiency furnaces, spa heaters, pool heaters, unit heaters, and water heaters. Connections use a factory installed double fail-safe self-sealing gasket, so assembly stays quick and professional on the job site. Tee styles include single wall tees, double wall tees, and boot tees, and the double wall boot tee provides a low flow resistance connection between horizontal and vertical sections. On double wall runs, the tee cap is sold separately from the tee, so the order has to cover both parts. Choosing the correct tee early keeps the vent layout straight, keeps condensate handling in mind, and prevents the parts mix-ups that stall an installation on a high efficiency appliance.
Subcategories
Buying Guide
Start with the vent construction already specified for the job. Single wall and double wall Z-Vent runs have separate tee part numbers, 2SVST for single wall and 2SVDT for double wall, so confirm the wall type before anything else.
Next, match the appliance. The double wall Z-Vent system is designed for Category II, III, and IV heating equipment, so check the appliance category on the nameplate and in the manufacturer's venting instructions before ordering.
Confirm the diameter. Z-Flex lists tee caps with drain in sizes from 3 to 24 inches, and its Z-Vent Dimensional Data document carries the complete list of parts.
Pick the tee style by layout. A standard tee connects horizontal and vertical sections, while the double wall boot tee gives a low flow resistance connection between them.
When ordering Z-Vent Tees, plan the cap at the same time. The double wall tee and double wall boot tee are both sold without a tee cap, and Z-Flex states that a tee cap with drain is required at the base of a vertical stack. High temperature silicone tubing for the drain is a separate purchase.
Finally, think through the connection. Z-Vent double wall connections use a factory installed double fail-safe self-sealing gasket, so gather matching pipe and fittings together and follow Z-Flex installation instructions for support and clearances.
Frequently Asked Questions
What does a Z-Vent tee do in a vent run?
Z-Vent Tees connect horizontal and vertical vent sections in a Z-Flex gas vent system. Z-Flex offers a single wall tee under part number 2SVST and a double wall tee under part number 2SVDT. Pick the one that matches the wall construction of the run.
Does a Z-Vent double wall tee come with a tee cap?
A Z-Vent double wall tee is sold without a tee cap, according to Z-Flex. The double wall boot tee is also sold with the tee cap separate. Add the cap to the same order so the vent run can be finished.
Where does a tee cap with drain go on a Z-Vent run?
On a Z-Vent run, Z-Flex states that a tee cap with drain is required at the base of a vertical stack. The tee cap with drain is listed in 3 to 24 inch sizes, and high temperature silicone tubing is a separate purchase. Confirm the diameter against the vent pipe before ordering.
What appliances are Z-Vent double wall tees designed for?
Z-Vent double wall tees are part of a system designed for Category II, III, and IV heating equipment. Z-Flex names boilers, high efficiency furnaces, spa heaters, pool heaters, unit heaters, and water heaters as the intended equipment. Always verify the appliance venting requirements before selecting fittings.
What is the difference between a Z-Vent double wall tee and a boot tee?
Both Z-Vent Tees connect horizontal and vertical sections of a double wall run, and both are sold without a tee cap. The double wall tee is part number 2SVDT, while the double wall boot tee is part number 2SVDTBT. Z-Flex describes the boot tee as a low flow resistance connection of those sections.