18S Series 1-1/2 HP Sewage Pumps are Little Giant submersible pumps built to move effluent and sewage waste in residential, commercial, industrial, and agricultural applications. Each 18S-CIM pump pairs a 1-1/2 HP motor with a 3-inch FNPT discharge and handles solids with a 2-inch diameter. Rated flow is 160 GPM at 10 feet of total dynamic head, and maximum head is 64 feet. The housing and volute are epoxy-coated cast iron, the impeller is brass, and the hardware is stainless steel. Maximum liquid temperature is 140°F. The series covers single-phase and three-phase power, with models 520300 through 520304 spanning 208V, 230V, and 460V options. Matching voltage and phase to the panel is the first step before any pump gets ordered. Choosing the correct 18S model matters because a pump sized to the actual head and solids load runs cooler, clogs less, and cuts callbacks.
Subcategories
Buying Guide
Start with the electrical supply, because it decides the model. Single-phase service calls for the 208V or 230V models, and three-phase service calls for the 208V, 230V, or 460V versions. Confirm panel voltage and breaker capacity first, since the single-phase pumps draw 16 amps and the three-phase pumps draw 5.3 amps.
Next, check the solids load and the head. Every pump in the 18S Series 1-1/2 HP Sewage Pumps category handles solids with a 2-inch diameter, delivers 160 GPM at 10 feet of total dynamic head, and reaches a maximum head of 64 feet. Calculate the total dynamic head of the system, including static lift and friction loss in the discharge line, and compare it to the pump's rating before ordering.
Then match the discharge. The 3-inch FNPT outlet needs compatible piping and a check valve, so confirm the basin and plumbing can accept it. Verify the liquid stays within the 140°F maximum temperature.
Finally, consider the switch and cord. Model 520301 uses a manual switch, and models 520300, 520301, 520302, and 520303 are listed with a 20 foot cord. Measure the run from the basin to the disconnect before settling on cord length, and confirm the float or control setup separately.
Matching voltage, head, and solids rating to the job keeps the pump running cool and cuts early failures.
Frequently Asked Questions
What solids can 18S Series 1-1/2 HP Sewage Pumps handle?
18S Series 1-1/2 HP Sewage Pumps handle solids with a 2-inch diameter. The brass impeller and epoxy-coated cast iron housing are built for effluent and sewage waste transfer. Anything larger than that diameter falls outside the rating.
What discharge size do the 18S sewage pumps use?
The 18S Series 1-1/2 HP Sewage Pumps use a 3-inch FNPT discharge. Plan for matching piping and a check valve before installation. Confirm the existing basin plumbing can accept the 3-inch connection.
What flow rate does a 1-1/2 HP 18S sewage pump deliver?
The 18S Series 1-1/2 HP Sewage Pumps are rated for 160 GPM at 10 feet of total dynamic head. Maximum head is 64 feet. Flow falls as system head increases, so size the pump against the real head on the job.
Do 18S sewage pumps come in single-phase and three-phase?
Yes, the 18S Series 1-1/2 HP Sewage Pumps cover both. Single-phase models run on 208V or 230V, and three-phase models run on 208V, 230V, or 460V. Check the model number against the site's electrical service before ordering.
What is the maximum liquid temperature for an 18S sewage pump?
18S Series 1-1/2 HP Sewage Pumps are rated for liquids to 140°F. Check any hot discharge against that limit before the pump goes into service. The housing is epoxy-coated cast iron with stainless steel hardware.