Cash Acme BFP Backflow Preventers are dual check valves that stop contaminated water from siphoning back into a potable supply line when pressure drops or reverses. Each valve uses two spring-loaded poppet check modules inside a brass body, backed by a stainless steel spring and an internal strainer screen that keeps debris out of the sealing surfaces. The BFP series is certified to ASSE 1012 and CSA B64.3, ratings that many local plumbing codes require for low-hazard cross-connection points like boiler feed lines, trap primers, and livestock waterers. Rated for up to 170 psi and 180 degrees Fahrenheit, the valve handles typical hot and cold potable water conditions without added protection. Plumbers install these units wherever a connection could let non-potable water flow backward into the supply, protecting the rest of a building's water system from contamination with a single compact fitting.
Subcategories
Buying Guide
Selecting the right backflow preventer starts with identifying the hazard level at the connection point. Low-hazard, non-health applications like boiler feed lines, trap primers, and livestock waterers typically call for a dual check valve rather than a more complex reduced-pressure zone assembly, and many local plumbing codes accept ASSE 1012 or CSA B64.3 certified valves for these connections. Size the valve to match the existing pipe diameter; a 1/2-inch valve suits smaller residential and light commercial lines, while a 3/4-inch valve handles larger commercial or agricultural flow demands without restricting output. Connection style depends on how often the valve might need service. Cash Acme BFP Backflow Preventers with threaded union connections unscrew for cleaning or replacement without cutting into the pipe, which helps in boiler rooms and mechanical spaces that see periodic inspections. Sweat connection models suit new construction where a permanent joint is preferred and the valve is unlikely to need removal. Confirm the application stays within the 170 psi and 180 degree Fahrenheit rating shared across the BFP lineup, since higher pressure or temperature applications may need a different valve type entirely. Always check local plumbing code requirements before installation, since some jurisdictions specify a particular certification or valve type for a given cross-connection hazard, and a licensed plumber should verify code compliance before finalizing a backflow prevention plan for any commercial or agricultural application.
Frequently Asked Questions
Where are Cash Acme BFP backflow preventers typically installed?
Cash Acme BFP backflow preventers protect low-hazard, non-health cross-connections such as boiler feed lines, trap primers, chlorinator feed lines, and livestock waterers. Plumbers install the valve wherever a reversal in pressure could let non-potable water flow back into a potable supply line. The dual check design suits connections where a full reduced-pressure zone assembly isn't required by code.
What size BFP valve fits a typical boiler feed line?
Most boiler feed line and trap primer connections use a 1/2-inch BFP dual check valve, while larger commercial or agricultural applications often call for a 3/4-inch valve. Both sizes carry the same 170 psi and 180 degree Fahrenheit rating, so pressure and temperature limits stay consistent across the lineup. Checking the existing pipe diameter before ordering avoids a mismatched connection.
What certifications does the Cash Acme BFP series carry?
The BFP series is certified to ASSE 1012 and CSA B64.3, standards that many local plumbing codes reference for low-hazard backflow protection. Certification confirms the dual check modules meet minimum performance requirements for preventing backflow under varying pressure conditions. A licensed plumber should confirm which certification a specific jurisdiction requires before installation.
Can a BFP valve be serviced without cutting into the pipe?
Threaded union models thread directly into the pipe run and unscrew for cleaning, inspection, or replacement without disturbing the surrounding piping. Sweat connection models solder permanently into copper pipe and are better suited to installations that won't need frequent service. Choosing a union connection makes sense for equipment rooms where periodic inspection is expected.
What pressure and temperature range can a Cash Acme BFP valve handle?
Cash Acme BFP dual check valves carry a maximum rating of 170 psi and 180 degrees Fahrenheit across both the 1/2-inch and 3/4-inch sizes. Applications that exceed either limit need a different valve type rather than the standard BFP dual check. Staying within these ratings keeps the internal spring-loaded poppet modules sealing correctly over the life of the valve.