Radiant Mixing Blocks are packaged hydronic components that combine variable speed injection mixing, circulation, and air elimination into a single unit for radiant heating systems. The Taco RMB-1 covers a flow range of 0 to 15.5 GPM and a head range of 0 to 15 feet, rated to a maximum fluid temperature of 185 degrees Fahrenheit and a maximum working pressure of 125 psi. Installation requires only four pipe connections through a 3/4 inch NPT connection size, eliminating the closely spaced tees, external controls, and additional wiring a traditional injection mixing setup normally needs. The block can run as an outdoor reset control, a set-point control, or a delta-T limiting control depending on how the system is configured. Radiant floor heating systems depend on precise supply water temperature control to avoid overheating flooring materials, which is why consolidating mixing, pumping, and air elimination into one factory-assembled block simplifies both the design and the install.
Subcategories
Buying Guide
Specifying a radiant mixing block starts with flow rate, since undersizing the block limits how much heat the system can move through the tubing loops it feeds. The Taco RMB-1 covers 0 to 15.5 GPM, so calculate the total flow needed across every zone the block will serve before assuming one unit covers the whole system. Head range matters just as much on larger installations, where a 0 to 15 foot rating needs to cover the resistance of the longest loop plus any manifolds or zone valves in the circuit. Control mode is the next decision, and it depends on what the flooring and the design call for. A Radiant Mixing Block set to outdoor reset control adjusts supply temperature automatically as outdoor conditions change, which suits most whole-house radiant systems. Set-point control instead holds a fixed supply temperature, useful for a single slab pour with a defined design temperature. Delta-T limiting control caps the temperature swing between supply and return water, a setting worth choosing whenever the job involves engineered wood or another flooring material sensitive to thermal stress. Temperature and pressure limits apply across every mode: 185 degrees Fahrenheit maximum fluid temperature and 125 psi maximum working pressure cover the block's full operating range regardless of which control mode is active. Connection size is fixed at 3/4 inch NPT across all four required pipe connections, so confirm that size matches the existing manifold and boiler piping before ordering, since the block doesn't ship with reducing fittings to bridge a mismatch.
Frequently Asked Questions
What's the flow range on a radiant mixing block?
The Taco RMB-1 radiant mixing block covers a flow range of 0 to 15.5 GPM with a head range of 0 to 15 feet. Calculating total flow demand across every zone the block feeds is the first step before assuming one unit covers a whole system. Larger systems may need the flow and head range checked against the longest loop in the circuit.
How many pipe connections does a radiant mixing block need?
A radiant mixing block requires only four pipe connections through 3/4 inch NPT fittings, replacing the closely spaced tees and external controls a traditional injection mixing setup needs. Fewer connections simplify both the piping layout and the wiring on a radiant install. The connection size stays the same across every control mode the block supports.
What control modes does a radiant mixing block support?
A radiant mixing block supports outdoor reset control, set-point control, and delta-T limiting control. Outdoor reset adjusts supply temperature based on outdoor conditions, set-point holds a fixed target temperature, and delta-T limiting caps the swing between supply and return water. Choosing a mode depends on the flooring material and the design intent of the radiant system.
What's the maximum fluid temperature a radiant mixing block can handle?
A radiant mixing block is rated to a maximum fluid temperature of 185 degrees Fahrenheit and a maximum working pressure of 125 psi. Both limits apply regardless of which control mode is active. Staying within these limits protects the block's internal components over the life of the system.
When should delta-T limiting control mode be used on a radiant mixing block?
Delta-T limiting control mode caps the temperature difference between supply and return water, which protects flooring materials like engineered wood from thermal stress. Contractors installing radiant heat under wood flooring commonly choose this mode over outdoor reset or set-point control. The mode runs through the same four-connection installation as every other control option on the block.