WarmWire Floor Heating Cable is a loose radiant heating cable installers weave back and forth across a subfloor to add electric warmth under tile, stone, or similar hard flooring. The 120-volt lineup runs from a 20 square foot cable at 78 feet in length and 2.0 amps up to a 100 square foot cable at 391 feet in length and 10.0 amps, giving installers a size that matches almost any bathroom, kitchen, or entryway footprint without cutting a cable short. Because it ships as a bare cable rather than a pre-set mat, installers weave it around toilet flanges, cabinets, and other fixed obstacles that a rigid mat can't work around. Manufacturer specifications call for installation under tile and stone flooring specifically, so confirming the finish flooring type before ordering avoids a mismatch between the heating cable and what's going on top of it. For remodel jobs where the floor plan isn't a simple rectangle, that flexibility matters more than a fixed-size mat would offer.
Subcategories
Buying Guide
Measure the actual floor area needing heat before picking a cable size, then round up rather than down, since the cable can't be lengthened or shortened once ordered and running short mid-installation means stopping the job to order a second cable. The 120-volt lineup runs from a 20 square foot cable at 2.0 amps up to a 100 square foot cable at 10.0 amps, so matching the cable size to the room's square footage, not just its general size category, keeps the amperage draw predictable. Confirm the finish flooring before ordering, since WarmWire Floor Heating Cable is specified for installation under tile and stone rather than floating floors, laminate, or carpet, and installing under an unsupported flooring type risks both poor heat transfer and a flooring warranty conflict. Check the electrical panel's available capacity next, particularly on the larger 100 square foot cable, which draws 10.0 amps and can use up most of a dedicated 15 amp circuit on its own. Where a room's layout includes toilet flanges, cabinets, or other fixed obstacles, plan the weave pattern around those obstacles before starting, since the loose cable format allows routing around fixtures that a pre-set mat can't accommodate. Order slightly more cable coverage than the bare minimum square footage calculated, since spacing the cable a bit tighter than the loosest allowed pattern uses more cable per square foot but delivers more even heat across cold spots near exterior walls or large windows.
Frequently Asked Questions
What size WarmWire cable covers a small bathroom floor?
The 20 square foot cable, running 78 feet in length at 2.0 amps, covers most single small bathroom or powder room floors. The 25 square foot cable, at 98 feet and 2.5 amps, fits slightly larger layouts. Rounding up to the next size rather than down avoids running short mid-installation, since the cable length is fixed once ordered.
Can WarmWire cable go under vinyl or laminate flooring?
WarmWire Floor Heating Cable is specified for installation under tile and stone flooring rather than floating floors, laminate, or carpet. Installing it under an unsupported flooring type risks poor heat transfer and can conflict with the flooring manufacturer's own warranty terms. Confirming the finish flooring type before ordering the cable avoids a mismatch between the two products.
How much electrical capacity does a 100 square foot WarmWire cable need?
The 100 square foot cable draws 10.0 amps on a 120-volt circuit, which can use up most of a dedicated 15 amp breaker on its own. Electricians confirm the panel has available capacity before rough-in, since this size draws considerably more than the smaller 20 or 25 square foot cables in the lineup. Planning the circuit around the specific cable's amperage, not just the square footage, keeps the installation up to code.
Can WarmWire cable route around a toilet flange or cabinet base?
The cable ships loose rather than pre-set into a mat, so installers weave it back and forth around toilet flanges, cabinet bases, and other fixed obstacles as they lay it out. That flexibility is the main reason installers pick cable over a rigid mat on irregular room layouts. Spacing the weave pattern tighter near cold spots, such as exterior walls, delivers more even heat in those areas.
Does WarmWire cable need a specific thermostat?
WarmWire cable pairs with a compatible programmable thermostat sized to the cable's amperage draw for the installed square footage. Matching the thermostat's rated amperage to the cable size keeps the control from being undersized for the load. Electricians confirm the thermostat and cable are rated for the same 120-volt circuit before final hookup.