Premium Simplex Systems are packaged sewage and effluent pump systems that combine a single submersible pump, a sealed basin, and a float switch into one ready-to-install unit for below-grade plumbing fixtures. Standard packages use an 18 inch by 30 inch high-density polyethylene or structural foam basin paired with a 4/10 HP or 1/2 HP sewage pump, while the Pit+Plus SR option upgrades to a 20 inch by 30 inch roto-molded basin and a 1 HP grinder pump for handling solids. Every pump in the lineup runs at 115 volts with a 2 inch discharge as standard, so plumbers wire and plumb a single package rather than assembling a pump, basin, and switch from separate parts. Basement bathrooms, below-grade laundry rooms, and additions built under the main sewer line all depend on a self-contained simplex package to lift waste to the gravity line, which is why matching the right horsepower and basin size to the fixture load matters before the pit gets poured.
Subcategories
Buying Guide
Choosing the right simplex package starts with the fixture load feeding the pit, not the pump horsepower. Count the drains and fixtures that will discharge into the basin, then match that volume against the basin capacity, since an 18 inch by 30 inch basin holds less reserve than the 20 inch by 30 inch option used on the Pit+Plus SR. Horsepower comes next: a 4/10 HP pump covers typical single-bathroom or laundry room loads, while 1/2 HP handles heavier flow, and a 1 HP grinder pump becomes the right call whenever the discharge line is long, narrow, or runs uphill before it reaches the main sewer line. Basin material is a secondary decision. Standard high-density polyethylene works for most residential pits, but structural foam holds up better under a driveway, patio, or any area carrying surface load above the pit. Premium Simplex Systems also standardize the discharge connection at 2 inches, so confirm that size lines up with the existing waste line before ordering, since a mismatch means adding a reducer or upsizing the run. Voltage is consistent at 115 volts across the standard lineup, which simplifies electrical planning on most residential jobs. Finally, check whether the project needs an upsized 24 inch by 36 inch or 30 inch by 36 inch basin instead of the standard size, since larger basins reduce cycling frequency on jobs with multiple fixtures feeding a single pit.
Frequently Asked Questions
What's the difference between a simplex sewage pump and a simplex grinder system?
A simplex sewage pump package moves liquid waste and soft solids using a 4/10 HP or 1/2 HP pump, while a Pit+Plus SR grinder system uses a 1 HP pump to shred solids before they leave the basin. Grinder systems make sense on long, narrow, or uphill discharge runs where solids could clog standard piping. Both configurations use a sealed basin with a float switch for automatic operation.
What basin size comes standard with a premium simplex package?
Standard simplex packages use an 18 inch by 30 inch basin, while the Pit+Plus SR grinder system uses a 20 inch by 30 inch basin. Larger 24 inch by 36 inch and 30 inch by 36 inch basins are available as accessories for jobs with multiple fixtures feeding one pit. Basin size should match the fixture load and available storage volume between pump cycles.
What discharge size do these systems use?
Premium Simplex Systems standardize on a 2 inch discharge connection across the standard package lineup. Confirming that the existing waste line matches this size before ordering avoids adding a reducer fitting on installation day. The vent connection is sized the same as the discharge on most configurations.
What voltage do simplex sewage pump systems run on?
Simplex sewage pump systems in the standard lineup run on 115 volts, which keeps electrical planning consistent across residential installations. The 4/10 HP, 1/2 HP, and 1 HP grinder pump options all share this voltage requirement. A dedicated circuit sized to the pump's amperage still applies regardless of horsepower.
When does a job call for a structural foam basin instead of polyethylene?
Structural foam basins fit the same 4/10 HP and 1/2 HP simplex pump packages as standard polyethylene basins but hold up better under surface loading. Pits located under a driveway, patio, or another load-bearing area benefit from the added rigidity. Float switch and discharge fittings stay the same between the two basin materials, so switching doesn't change the rest of the installation.