Bluefin Stainless Steel Radiant Heat Manifolds are modular supply-and-return assemblies that distribute hot water to individual radiant floor heating loops from a single stainless steel body. The lineup spans 2-loop through 12-loop configurations, so installers can match a manifold to the exact number of zones a job requires instead of over-sizing. Every manifold runs a temperature range of 0 to 185 degrees Fahrenheit with a maximum rating of 194 degrees, and connects through a 1 inch FPT main inlet with EK20 loop threads compatible with both PEX and PEX-AL-PEX tubing. Supply-side balancing valves let a technician adjust flow rate on each loop independently, while the return side includes valves set up for thermal actuators tied into zone control wiring. Radiant heating contractors specify these manifolds when a job needs precise circuit-by-circuit flow control across a multi-zone floor heating system, which keeps room temperatures even across different floor areas and loop lengths.
Subcategories
Buying Guide
Loop count drives the first decision. Counting the separate radiant zones a project needs, from a single bathroom floor up to a whole-house system, points directly to a manifold size between 2 and 12 loops. Oversizing a manifold adds unused ports and cost without benefit, while undersizing forces a second manifold station and extra piping runs back to the mechanical room.
Tubing type matters next, since the loop connections need to match what's actually in the floor. Bluefin Stainless Steel Radiant Heat Manifolds connect to both PEX and PEX-AL-PEX tubing through the same EK20 loop thread, so manifold choice doesn't narrow based on tubing type.
Flow control requirements come next. Jobs that need to balance flow rate across loops of different lengths benefit from the supply-side balancing valves built into every model, which let a technician dial in each loop independently rather than relying on even flow distribution across loops that vary in length and heat load. Projects using zone control additionally need return-side valves set up for thermal actuators, such as the HMACT4, to open and close individual loops based on a thermostat call.
Temperature rating rarely becomes a limiting factor, since every model in the line runs up to 185 degrees Fahrenheit with a 194 degree maximum, well above typical radiant floor supply temperatures. Matching loop count and tubing type to the project, then confirming flow control and actuator needs, covers the core sizing decision for most radiant installations.
Frequently Asked Questions
How many loops do Bluefin Stainless Steel Radiant Heat Manifolds support?
The line spans 2-loop through 12-loop configurations, covering the HM2, HM3, HM4, HM5, HM6, HM7, HM8, HM10, and HM12 models. Loop count should match the number of separate radiant zones a project needs rather than defaulting to the largest available size. Every size shares the same stainless steel construction and temperature rating regardless of loop count.
What tubing types work with Bluefin manifolds?
Bluefin Stainless Steel Radiant Heat Manifolds connect to both PEX and PEX-AL-PEX tubing through a shared EK20 loop thread. Tubing choice doesn't limit which manifold size works for a project. Matching adapter fittings to the tubing's outer diameter still matters during installation.
Can flow be balanced across individual loops on these manifolds?
Yes, every Bluefin manifold includes supply-side balancing valves that let a technician adjust flow rate on each loop independently. Independent balancing matters most when loops vary in length or heat load across a radiant zone. The feature applies across every loop count in the line, from the 2-loop HM2 up to the 12-loop HM12.
Are these manifolds compatible with zone control actuators?
Yes, the return side of each manifold includes valves set up to accept thermal actuators, such as the HMACT4 4-wire normally closed actuator, for zone control wiring. Actuators open and close individual loops based on a thermostat call. Actuator-based control lets a single manifold station serve multiple independently controlled zones.
What's the maximum operating temperature for Bluefin manifolds?
Every manifold in the line runs within a 0 to 185 degree Fahrenheit range, with a maximum rating of 194 degrees. The range covers typical radiant floor supply temperatures with margin to spare. Temperature rating stays constant across every loop count, from the smallest HM2 to the largest HM12.