Taco 2400 Series In-Line Pumps are flanged circulator pumps built for hydronic heating, chilled water cooling, and hot water recirculation in medium to high flow applications. The line covers a flow range of 0 to 90 GPM and a head range of 0 to 46 feet, with a maximum working pressure of 150 psi and an operating temperature range of 40 to 225 degrees Fahrenheit. Connection sizes run from 3/4 inch through 3 inch, so the same product family covers a residential zone circulator up through a larger commercial loop. Each pump uses a close-coupled, maintenance-free motor with permanently lubricated, sealed bearings, paired with a stainless steel shaft, a Noryl impeller, and a carbon and silicon-carbide mechanical seal. Horsepower options range from 1/10 HP up to 1/2 HP, and the body is available in cast iron or stainless steel depending on the fluid being circulated. Mechanical contractors specify this series when a project needs more flow or head capacity than a smaller circulator can deliver, without stepping up to a base-mounted end suction pump.
Subcategories
Buying Guide
Sizing starts with the system's calculated flow and head requirements, since matching a pump to actual load prevents both wasted energy and inadequate circulation. Pull the heat loss or cooling load for the zones being served, convert that to a required GPM, and check it against the flow and head range of each horsepower option before settling on a specific model. Once flow and head are confirmed, connection size narrows the choice further. Taco 2400 Series In-Line Pumps are flanged in sizes from 3/4 inch through 3 inch, so match the flange to the pipe size already specified for the mechanical room rather than forcing a reducer at the pump. Material selection comes next: cast iron suits closed-loop hydronic heating and chilled water systems, while stainless steel is the right call for domestic hot water recirculation or any application where cast iron could corrode from the fluid being moved. Pressure and temperature also matter on larger commercial jobs. Confirm that a 150 psi working pressure and a 225 degree Fahrenheit maximum operating temperature cover the system's design conditions, since exceeding either limit calls for a different pump family entirely. Finally, factor in maintenance access: the close-coupled, sealed-bearing motor design used across the line needs little routine service, but confirm there is enough clearance around the pump body to pull the motor cartridge for a seal replacement down the road.
Frequently Asked Questions
What is the flow and head range of Taco 2400 Series In-Line Pumps?
Taco 2400 Series In-Line Pumps cover a flow range of 0 to 90 GPM and a head range of 0 to 46 feet across the horsepower lineup. Matching a specific model to a calculated system load keeps the pump correctly sized rather than oversized or undersized for the zones it serves.
What is the maximum pressure and temperature rating for these pumps?
Taco 2400 Series In-Line Pumps carry a maximum working pressure of 150 psi and an operating temperature range of 40 to 225 degrees Fahrenheit. The ratings cover typical closed-loop hydronic heating, chilled water, and hot water recirculation systems.
When should a cast iron pump be used instead of stainless steel?
Cast iron construction fits closed-loop hydronic heating and chilled water systems where the circulated fluid is treated system water. Stainless steel construction is the better choice for domestic hot water recirculation or any open-loop application where cast iron would corrode over time.
What connection sizes are available on the 2400 Series?
Taco 2400 Series In-Line Pumps are flanged in connection sizes from 3/4 inch through 3 inch. Matching the flange size to the existing pipe size avoids adding a reducer fitting at the pump connection.
What horsepower options are available for the 2400 Series?
Taco 2400 Series In-Line Pumps come in 1/10 HP, 1/6 HP, 1/3 HP, and 1/2 HP motor options. Smaller motors suit single-zone residential circulation, while the larger horsepower options handle bigger commercial loads or multiple zones on one pump.