| Application: | Heat Only Electric Heat (Line Voltage) |
|---|---|
| Stages: | 1 Heat |
| Programmability: | Programmable 7 Day |
| User Interface: | Push Button |
| Mount: | Vertical |
| Options: | Large Display |
| Power Method: | Hardwired |
| Voltage: | 240v Line voltage 208V |
| Temperature Range (F): | 40°F - 86°F |
| Switch: | DPST |
| Wattage: | 3120 to 3600 |
| Wiring: | 5-1/2" Tinned Copper Leadwires |
| Frequency: | 50 Hz 60 Hz |
| Color: | Premier White |
| Height: | 4-7/8" |
| Width: | 2-3/4" |
| Depth (Inches): | 7/8" |
| Wireless: | No |
| Humidity Control: | No |
Hello Stan, unfortunately no. Since they are two different types of line volt thermostats they would not replace one another as the TH115AFGA is still a available part.
No, that thermostat is hardwired.
No it will not, its heat only.
Hi, Garry - The thermostat is constructed as a two-pole (meaning it can switch two live lines) single-throw (meaing on-off). The one of the two black wires are for one 'hot' leg of the power source being used (204-240 VAC) and the other black goes to the unit being supplied with power. Same applies to the white wires. So, to hook it up to a 204-240 VAC heater, remove the old thermostat and disconnect the wires. Usually, in a two-wire system, a black wire from the main supply goes to one side of the switch and the other black lead hooks to one side of the device being used. The white wires are most often tied together and go directly from the power supply (fuse box) to the heater. In this configuration, the switch being used is a single-pole single-throw, meaning only one leg of the supply line is being switched. You'll want to make sure that you separate the main power supply wires from the heater wires so you have a white and black coming from the fuse box (or junction box) and a white and black wire coming from the heater. Now, connect the black power supply lead to one black lead on the thermostat (it should show as "line" and connect the white lead from the power supply (or junction box) to the white lead shown as "line" on the thermostat. You can now connect the leads from the heater to the corresponding white and black leads on the thermostat (shown as "load"). Make sure that any copper ground wires are connected for shock protection and you should be set to go. These are great thermostats and I've been very happy with the three I purchased several heating season's ago. Hope they meet your needs, as well.
This is a line voltage 240volt 2 pole t-stat. Two wires from source (240v) two wires to heater (load) Sent from my iPhone
Yes, this thermostat is a 7 day programmable unit so a different program can be set up for each day of the week.
Yes it's a 7 day programmable. Sent from my Samsung Galaxy Tab® S
Yes u can program each day Sent from my Verizon Wireless 4G LTE smartphone
Yes, each day of the week can be individually programmed.
YES, it is truly a seven day thermostat. Not a 5 day, and a 2-day version. Sat. is different from Sunday.
Yes, you can program each day individually.
Yes this thermostat allows 7 individual settings - one for each day of the week. John
Yes you can program each day of the week Sent from my iPhone
we dont have the specs to match a Mears, if you call w your requirements we can find a replacement
we would need the electrical specs on the heaters, not the sizes.
The load calculation baseboard heat is 250 Watts per foot (as seen fit by those in the electrical installation/design field). Then get rated components that can withstand 125% of that calculated load. So, you have a total of 20 feet of baseboard heat. That is 5000 watts. An additional 25% is 1250 watts. 6250W / 240V = 26 Amps. These are rated for 15 amps each. Side note: your heaters are not wired in series (at least, they should not be). If they are on the same circuit then that circuit is a 30A circuit. You are likely better having a t-stat for each of the heating units. Then none of those units will exceed the amp rating of this t-stat.
no it can not.
No, this is a line volt thermostat designed for use with electric heating and not for 24 volt systems. The direct replacement for the CT87K is model T87K1007 which is available here: http://www.supplyhouse.com/Honeywell-T87K1007-Round-Mercury-Free-Heat-Only-Thermostat-Premier-White-4908000-p
Yes, as long as you don't exceed the wattage rating of the thermostat. Typically an electric baseboard heater is 250 watts per foot of length at 240 volts ac. So a 5 foot baseboard would be 1250 watts at 240vac. Two 5 footers would be 2500 watts. Which would be about 10.5 amps. Two 8 footers would be 4000 watts and 16.5 amps. Sent from my Verizon Wireless 4G LTE DROID
yes, as long as you don't exceed the spec for the thermostat.
I have 3 baseboard heaters connected to mine. Just be careful that the combined wattage of the heaters does not exceed the capacity of the thermostat. Sent from my iPad