Tubular Flanged Tailpieces are the drain fittings that connect a sink or lavatory drain outlet to a P-trap, using a flanged end that seats against the sink strainer or basket and a plain end that slips into the trap's slip-joint nut. Plumbers install these on kitchen sinks, bar sinks, and lavatories any time the drain assembly needs a straight connection between the strainer and the trap. Danco's 1-1/2 inch O.D. by 4 inch flanged tailpiece is a common example, sold with a waste arm plus two slip nuts and washers included for a complete connection. Lengths vary to match the distance between the strainer outlet and the trap, so a longer or shorter tailpiece gets selected based on cabinet depth and drain rough-in height rather than a single universal size. Material choice, plastic or chrome-plated brass, generally depends on whether the fitting is visible on an open vanity installation or concealed inside a closed cabinet where appearance matters less.
Subcategories
Buying Guide
Diameter is the first measurement to confirm, and it should match the strainer outlet rather than the trap. Standard kitchen and lavatory sinks use 1-1/2 inch tailpieces, while bar sinks and smaller fixtures often need a 1-1/4 inch size instead. A reducing washer at the trap connection handles any mismatch between tailpiece and trap diameter, so getting the tailpiece-to-strainer match right matters more than matching the trap size directly.
Length comes next, measured from the strainer outlet to where the trap connection needs to land. Fixed-length tailpieces come in several standard lengths, and picking one close to the actual cabinet depth avoids excess pipe that needs trimming. For jobs where cabinet depth varies or isn't known ahead of time, a slip-joint extension tailpiece that expands or compresses in place removes the need to carry several fixed lengths to the job site.
Material selection depends mostly on visibility and finish matching. Plastic versions of Tubular Flanged Tailpieces work fine where the fitting stays hidden inside a closed cabinet, and cost less than metal versions. Chrome-plated brass versions match exposed supply lines and traps on pedestal sinks or other installations where the drain assembly stays in view. Gauge thickness on brass tailpieces, typically 17 or 22 gauge, affects how the fitting holds up to repeated tightening at the slip nuts over the life of the fixture.
Frequently Asked Questions
What size tailpiece fits a standard kitchen sink?
Standard kitchen and lavatory sinks use a 1-1/2 inch tailpiece to match the typical strainer outlet size. Bar sinks and smaller fixtures often need a 1-1/4 inch tailpiece instead, since the drain outlet itself is smaller. Matching tailpiece diameter to the strainer, not the trap, prevents ordering the wrong size.
How is tailpiece length determined for a specific installation?
Length is measured from the strainer outlet to where the trap connection needs to sit, which varies by cabinet depth and drain rough-in height. Fixed lengths are available in several standard sizes, and picking one close to the actual measurement avoids excess pipe needing trimming. A slip-joint extension tailpiece works as an alternative when cabinet depth varies across a job.
When should a plastic tailpiece be used instead of chrome-plated brass?
Plastic tailpieces work well where the fitting stays hidden inside a closed vanity cabinet and appearance isn't a concern. Chrome-plated brass tailpieces match exposed supply lines and traps on pedestal sinks or other installations where the drain assembly remains visible. Cost and appearance are usually the deciding factors between the two materials.
What does gauge mean on a chrome-plated brass tailpiece?
Gauge refers to the thickness of the brass tubing used in the tailpiece, with 17 and 22 gauge both common in this category. A lower gauge number indicates thicker material, which typically holds up better to repeated tightening at the slip nuts. Choosing a heavier gauge matters most on fixtures that see frequent trap removal for cleaning or repair.
What comes included with a flanged tailpiece, or are slip nuts purchased separately?
Many flanged tailpieces, including Danco's 1-1/2 inch by 4 inch model, come complete with a waste arm plus two slip nuts and washers included. Checking the specific product listing confirms whether hardware ships with the tailpiece or needs to be purchased separately. A complete kit saves a trip back for missing slip nuts or washers on the same job.